I ordered Nist4 with Evo all for a Nissan Altima 2013 Push Start. Its a plug and play on the BCM behind the cluster. Everything went fine with programming, but when I try to start the car while I am inside with press brake and push button to start gives me error i-key start error, the engine ticks no turn over.

When I am outside to remote strt 3xLock, it starts!! but inside using the normal car starting keyfob it doesn’t? I decrypted the module twice and also and sometimes it ticks no start. I programed it to car twice everything went well, all the flashing when I was programming went exactly per book, help please??

- Option D6 is on

- ignition turns on but error message i-key error refer to user manual

- car ticks when I press brake and push start, but no start and error message i-key error refer to user manual

- sometimes with remote start 3xlock the car starts sometimes it just ticks like I am inside the car

- SN: 001A07 119247 EVO-ALL

2011 Altima Push-To-Start Using T-harness.  Connected to OBDII, Brake Pedal, Keybox.  Tapped into Brown wire on push-to-start button. A1-A11, C1, D1, D1.2, D3 Enabled Latest firmware for flasher and EVO-ALL

Went through programming sequence (with battery out of FOB).  Sequence completed sucessfully ending with rapid-flashing yellow light.  When activated with FOB inside vehicle, it starts fine with the 3x lock press.  With FOB removed from vehicle, 3x lock press does not start vehicle.  Vehicle displays "No key" message on instrument cluster.  

I have tried to re-flash and re-program the EVO-ALL multiple times, all with identical results.  

What am I missing here?

2011 Altima Push-To-Start Using T-harness.  Connected to OBDII, Brake Pedal, Keybox.  Tapped into Brown wire on push-to-start button. A1-A11, C1, D1, D1.2, D3 Enabled Latest firmware for flasher and EVO-ALL

Went through programming sequence (with battery out of FOB).  Sequence completed sucessfully ending with rapid-flashing yellow light.  When activated with FOB inside vehicle, it starts fine with the 3x lock press.  With FOB removed from vehicle, 3x lock press does not start vehicle.  Vehicle displays "No key" message on instrument cluster.  

I have tried to re-flash and re-program the EVO-ALL multiple times, all with identical results.  

What am I missing here?

Hi, I just installed EVO-NIST1 as per Installation Guide in my Nissan Altima 2012 (Push to Start - Auto transmission) for using my OEM Key Fob 3x to Remote Start and OEM Key Fob to Remote Shut Off.

Is it possible to switch on rear defroster /defrost when Remote Start ? if yes than where can I get the wiring connection diagram for Altima 2012 etc...

I'm using OEM Key Fob Only.

Thanks

I've installed EVO-NIST1 in Nissan Altima 2012 2.5S (Push to Start), connect all the cables as per installating guide. I'm using my OEM Key Fob to remote start by pressing lock 3x. I've configured EVO to run time 15mins. It's working fine after 15min car shutoff if you don't drive. But if I start remotely and dirve within 15mins ( unlocak car using Remote and dirve), Car SHUTOFF exactly 15min after I started remotely, even I'm driving. It happened with me more than 4 times, thank GOD I was on signal stop when 2 times it happned and the two time when I drove and was in parking lot. Car shutoff. I've to start by push to start.

These days what I'm doing is start car remotely so car can heat up and when I need to drive, I've to shut off by pressing break and start again to make sure car doesnt shutoff in middle of highway.

Let me know if I'm missing any configuraiton.

thanks

I've installed EVO-NIST1 in Nissan Altima 2012 2.5S (Push to Start), connect all the cables as per installating guide. I'm using my OEM Key Fob to remote start by pressing lock 3x. I've configured EVO to run time 15mins. It's working fine after 15min car shutoff if you don't drive. But if I start remotely and dirve within 15mins ( unlocak car using Remote and dirve), Car SHUTOFF exactly 15min after I started remotely, even I'm driving. It happened with me more than 4 times, thank GOD I was on signal stop when 2 times it happned and the two time when I drove and was in parking lot. Car shutoff. I've to start by push to start.

These days what I'm doing is start car remotely so car can heat up and when I need to drive, I've to shut off by pressing break and start again to make sure car doesnt shutoff in middle of highway.

Let me know if I'm missing any configuraiton.

thanks