English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

28/01/2021

 Kia Jake Randall (130Pts.)

0

Cant program '15 Kia Optima PTS

I have everything wired on my '15 KIA Optima Push to Start. When i go to program i get to the step where i push the button 7 times. The red LED never flashes 10 times and the blue never comes on after. When I hard wired CAN1 CAN2 wires, the wire diagram shows it connected to a wire in a harness in the driver side kick plate. But there are 2 wires in each pin in the harness. (2 white/orange wires, 2 white wires). DO i have to splice to BOTH of the wires in each pin placement? Or will connected to only 1 work? This is the only thing i can thing of why i can not get mine to program.
Connectez-vous pour répondre Voir 1 réponse(s)

18/05/2020

 Kia jon hatcher (450Pts.)

0

2012 soul standard key no can bus communication evo one

2012 Kia Soul standard key no immobilizer. Using thar-one-khy1. Blue light won't flash when programming. I can read codes and voltage to the fortin module white 5 pin matches obd output at around 2.37v low can and 2.67v high. Module,flashlink all at the latest firmware. Evo one flashes successfully. Just when key on it fails to finish programming. Also wired in the fortin hood switch. Any help? Since it's such a simple install it's embarrassing to ask for help. Should work and great instructions as usual.
Connectez-vous pour répondre Voir 2 réponse(s)

18/05/2020

 Kia jon hatcher (450Pts.)

0

2012 soul standard key no can bus communication evo one

2012 Kia Soul standard key no immobilizer. Using thar-one-khy1. Blue light won't flash when programming. I can read codes and voltage to the fortin module white 5 pin matches obd output at around 2.37v low can and 2.67v high. Module,flashlink all at the latest firmware. Evo one flashes successfully. Just when key on it fails to finish programming. Also wired in the fortin hood switch. Any help? Since it's such a simple install it's embarrassing to ask for help. Should work and great instructions as usual.
Connectez-vous pour répondre Voir 2 réponse(s)

20/10/2019

 Kia James Perdue (130Pts.)

0

EVO ALL CAN Bus confusion

Good evening, I am wiring up an EVO All with a Viper 4706V on a 2015 KIA Sorento. I am confused on the CAN1 and CAN 2 locations. According to guide 10841, CAN1 is located on the back of the fuse box, and CAN2 is located on the ODB-II connector. Yet, WIRECOLOR.com shows the opposite. And looking at the standard pinouts for ODB-II, it just shows can bus high and low on the ODB-II, no 1 or 2 spec. Anybody out there do one of these installs? Not sure which doc to trust here... Thanks, Jim
Connectez-vous pour répondre Voir 1 réponse(s)

09/10/2017

 Kia Billy Reed (210Pts.)

0

Can Wire Locations

I am working on installing an evo all as a stand alone alarm only on a 2011 kia soul pts by question is what are can 1 and 2? The fortin guide show can 1 at the obd plug and can 2 behind the cluster but wirecolor.com shows can 1 behind the cluster and can 2 at the obd! which one would be correct?
Connectez-vous pour répondre Voir 1 réponse(s)

13/03/2015

 Kia pilmooon jung (200Pts.)

1

2015 sedona won't program evo-all

i installed autostart with evo-all i used D2D and program perfect but door lock,unlock is not working and not detected hood pin,door status,brake s/w i rechecked can bus high,can bus low wires one side 5v,other side approx 0v so tried connect opposite side,but won't program also tried the other brand bypass module(idata) but no change i working at kia so i look at ours manual. 100% correctly connected CAN high and,low lines what i need to check now?
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer