English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

03/02/2023

 Jeep Nev (130Pts.)

0

Jeep has power but does not crank?

I have programmed the unit sn: 001A07 415854 Evo All. Installed with wiring harness THAR-CHR4 (Both Yellow wires on the harness are connected together). Programmed the unit. All these went according to the documentation, correct leds and all.

My vehicle is a 2011 Jeep Grand Cherokee 3.0CRD Limited with Start Button

I do the 3x Lock Blue Led comes on every time I press the lock button. Then all power comes on, a few seconds later the red and yellow led is solid and the radio shuts off just like it does while it cranks but no crank??

What could I be doing wrong?

Many Thanks!!

Connectez-vous pour répondre Voir 1 réponse(s)

16/01/2022

 Jeep Andy Sicard (200Pts.)

0

2005 Jeep Grand Cherokee, Turns on but no crank, no start.

Installing Evo All, stand alone with Thar-CHR5 harness. Ignition and MUX wires are connected, module is programmed, key is programmed. Dash lights up, fuel pump buzzes but not start. 

With the harness, I connected the yellow-yellow (ignition), green/red-purple (MUX), and white/red-pink/orange (starter) wires. is there something I'm missing?

Connectez-vous pour répondre Voir 2 réponse(s)

16/01/2022

 Jeep Andy Sicard (200Pts.)

0

2005 Jeep Grand Cherokee, Turns on but no crank, no start.

Installing Evo All, stand alone with Thar-CHR5 harness. Ignition and MUX wires are connected, module is programmed, key is programmed. Dash lights up, fuel pump buzzes but not start. 

With the harness, I connected the yellow-yellow (ignition), green/red-purple (MUX), and white/red-pink/orange (starter) wires. is there something I'm missing?

Connectez-vous pour répondre Voir 2 réponse(s)

08/12/2021

 Jeep Shane Benjie (220Pts.)

0

2007 Jeep Compass, turns on but no crank no start.

installing Evo All, stand alone with Thar-CHR5 ignition and MUX wires are connected module is programmed, key is programmed bit no start. Dash lights up, fuel pump buzzes but not start. HELP?
Connectez-vous pour répondre Voir 1 réponse(s)

22/03/2019

 Jeep Douglas Chase (130Pts.)

0

2012 Jeep Compass Turns on but doesnt crank EVO All

2012 Jeep compass, programming goes through sucessfully but pressing lock 3x will turn on everything, but doesnt actually crank. Using evo-all chrt5 harness. have yellow wire joined together, thats only one hooked up.
Connectez-vous pour répondre Voir 1 réponse(s)

09/01/2019

 Jeep Brent Blunier (160Pts.)

1

'07 Jeep GC, MUX voltage, key on- no crank, verifying wiring connections

2007 Jeep Grand Cherokee Diesel Automatic, EVO-CHRT5 T harness, standalone F diagram. 74.07 firmware, 6.0 hardware, Bypass checked "on"  are A1,3,7 C1, D1, D2, all other options are checked "off". OEM key programming was successful. When I push lock 3X the ingition comes on but engnine does not crank. I checked ignition connection after lock 3x, the power consant (white /blue) =12v and starter cranking (white/red) = 11.9v. The MUX voltage (VOM on green /red and chassis ground)  with no key =4.19v, key in=3.61v, key on=.993v, crank =.36v.... when remote starting "key on" =1.05v, "key off"=4.19v, cranking = .40V. .. I also have error codes/warnings ( trans temp, 4WD system fault) that appear on dash when it tries to remote start.  I have attached pic of wiring to the ingnition connection. I'm questioning MUX voltage and correct wiring? attached pics. the wires are soldered to pins in connector

Connectez-vous pour répondre Voir 2 réponse(s)

09/01/2019

 Jeep Brent Blunier (160Pts.)

1

'07 Jeep GC, MUX voltage, key on- no crank, verifying wiring connections

2007 Jeep Grand Cherokee Diesel Automatic, EVO-CHRT5 T harness, standalone F diagram. 74.07 firmware, 6.0 hardware, Bypass checked "on"  are A1,3,7 C1, D1, D2, all other options are checked "off". OEM key programming was successful. When I push lock 3X the ingition comes on but engnine does not crank. I checked ignition connection after lock 3x, the power consant (white /blue) =12v and starter cranking (white/red) = 11.9v. The MUX voltage (VOM on green /red and chassis ground)  with no key =4.19v, key in=3.61v, key on=.993v, crank =.36v.... when remote starting "key on" =1.05v, "key off"=4.19v, cranking = .40V. .. I also have error codes/warnings ( trans temp, 4WD system fault) that appear on dash when it tries to remote start.  I have attached pic of wiring to the ingnition connection. I'm questioning MUX voltage and correct wiring? attached pics. the wires are soldered to pins in connector

Connectez-vous pour répondre Voir 2 réponse(s)

31/10/2016

 Jeep Kyle Green (140Pts.)

1

2010 jeep liberty ignition comes on but no crank

i have a 2010 jeep liberty hooked up to a fortin evo-all which is data link connected to a crimestopper rs3-g5 remote start. it worked for a while but than all of a sudden it wouldnt crank. my electronics and ignition would come on but it wouldnt start. when the car is started it has the orange light on and when its remote started the red and orange light is on. any tips?
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer