English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

28/04/2017

 Jeep Michael C (160Pts.)

0

evo-one, 6 pin harness, rs programming, Wrangler

Hello, I require some assitance from you with an installation. I have been reviewing the diagrams shown in the install manual # 16561 and the quick install guide for the installation of an EVO-ONE with the CHR5 t-harness onto a 2016 Jeep Wrangler with manual transmission. I have also reviewed mutliple other EVO-ONE install guides as further information sources as well as searched the forum prior to asking this. So that you know where I am, here is what has been done so far: I have installed the valet switch. Connected the 3 pin to a dual stage shock sensor. On the 20 pin connector I have added a siren to pin A7, connected the hood pin to A15, and connected the A1 yellow to the t-harness yellow. On the 6 pin white connector, I have connected the white E1 wire to the white and purple parking light wire at the kick panel on the passenger side of the vehicle, connected the E3 power to an unswitched 12v power source, and connected the E4 ground to a suitable body ground location. Where I am lost is that on the white 6 pin connector, there are also the E2 orange, E5 pink, and E6 yellow wires that are currently unused. Addtionally, there is no reference to the use of any wires other that E1 and E3 on the instructional schematic. I assumed E4 ground due to E3 12v power is used. The EVO-ONE quick install guide states that E2 is (+) ACC/IGN2, E5 is (+) ignition, and E6 is (+) Starter. Additionally, while programming the unit with the flash link, function 2 and function 31 make reference to using the white, orange, pink, and yellow. I know that function 31 should be set to mode 4 since I am using the white wire for the parking lights. What I do not know is: A) In addtion to the wires I already have connected (E1, E3, E4) on the white 6 pin connector, what else needs to be connected and where? B) What mode should function 2 be set to in order to be consistent with the function 31 mode 4 setting? I am asking prior to final testing so at this time, I do not know if this will work as is set up currently. Just trying to get final confirmation of correct wiring for your product instead of frying either the unit or some wires in the vehicle. Thanks in advance for your help edited final line from firing to frying.
Connectez-vous pour répondre Voir 2 réponse(s)

28/04/2017

 Jeep Michael C (160Pts.)

0

evo-one, 6 pin harness, rs programming, Wrangler

Hello, I require some assitance from you with an installation. I have been reviewing the diagrams shown in the install manual # 16561 and the quick install guide for the installation of an EVO-ONE with the CHR5 t-harness onto a 2016 Jeep Wrangler with manual transmission. I have also reviewed mutliple other EVO-ONE install guides as further information sources as well as searched the forum prior to asking this. So that you know where I am, here is what has been done so far: I have installed the valet switch. Connected the 3 pin to a dual stage shock sensor. On the 20 pin connector I have added a siren to pin A7, connected the hood pin to A15, and connected the A1 yellow to the t-harness yellow. On the 6 pin white connector, I have connected the white E1 wire to the white and purple parking light wire at the kick panel on the passenger side of the vehicle, connected the E3 power to an unswitched 12v power source, and connected the E4 ground to a suitable body ground location. Where I am lost is that on the white 6 pin connector, there are also the E2 orange, E5 pink, and E6 yellow wires that are currently unused. Addtionally, there is no reference to the use of any wires other that E1 and E3 on the instructional schematic. I assumed E4 ground due to E3 12v power is used. The EVO-ONE quick install guide states that E2 is (+) ACC/IGN2, E5 is (+) ignition, and E6 is (+) Starter. Additionally, while programming the unit with the flash link, function 2 and function 31 make reference to using the white, orange, pink, and yellow. I know that function 31 should be set to mode 4 since I am using the white wire for the parking lights. What I do not know is: A) In addtion to the wires I already have connected (E1, E3, E4) on the white 6 pin connector, what else needs to be connected and where? B) What mode should function 2 be set to in order to be consistent with the function 31 mode 4 setting? I am asking prior to final testing so at this time, I do not know if this will work as is set up currently. Just trying to get final confirmation of correct wiring for your product instead of frying either the unit or some wires in the vehicle. Thanks in advance for your help edited final line from firing to frying.
Connectez-vous pour répondre Voir 2 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer