Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

29/06/2023

Ford smrick2 (190Pts.)

0

Why does it only honk now when I remote start

Installed evo all with my car telematics with 944 rf kit and has worked beautifully since 2019 with the occasional horn honking when I remote start but I had to remove module and wiring from dash for some audio upgrades now all it does is honk the horn when I try to remote start. Does not try to crank everything powers up as it should then nothing. Thats on first attempt 2nd attempt does even do that. I have since go in and tried to reprogram module as t

29/06/2023

Ford smrick2 (190Pts.)

0

Why does it only honk now when I remote start

Installed evo all with my car telematics with 944 rf kit and has worked beautifully since 2019 with the occasional horn honking when I remote start but I had to remove module and wiring from dash for some audio upgrades now all it does is honk the horn when I try to remote start. Does not try to crank everything powers up as it should then nothing. Thats on first attempt 2nd attempt does even do that. I have since go in and tried to reprogram module as t

23/11/2020

Ford G M (15640Pts.)

0

how to reset fortin evo-all firmware

Is it possible to reset firmware evo-all?

0

Unreliable starting, and key left in door chime on 2011 Mercury Mariner (Ford Escape)

I installed a EVO-FORT1 with the T harness into my 2011 Mariner, and everything went smoothly, including programming. After a couple of starts, I intermittently have been getting no starts, where you can see the blue LED flashes from the Canbus seeing the remote, the red LED turns on, all the accessories turn on, but the engine doesn't start. Sometimes, but not always, I get the key ignition chime after driving, but only if the T harness connected to the EVO module

0

EvoALL to turn on HVAC (Heater/Ac) rear defrost/mirrors on 2013 F150?

Have a Fortin EVO ALL on my 2013 F150. can it be used to tap into the OEM cabin sensor and allow for the AC and/or heater to be turned on when remote start is activated? Same thing with rear defrost and mirrors on cold days. the OEM remote start allows for this. Can the EVO ALL? if so, how do I proceed? Joe

0

key override wont program

i have an 04 f-150 with viper carstarter and fortin bypass. i try to program the bypass but it wont work this is what iam doing. 1 press hold button 2insert connection one 3insert connection 2 4put key in and turn to on untill security light goes out 5 remove key and insert second key and repeat step 4 remove key and activate remote start now the led should go out but it doent it flashes once then stays solid any ideas as to why it wont program.i have check and rechecked and checked again with my wiring and all looks ok even had some one else go over it and they cant see anything wrong

0

key override wont program

i have an 04 f-150 with viper carstarter and fortin bypass. i try to program the bypass but it wont work this is what iam doing. 1 press hold button 2insert connection one 3insert connection 2 4put key in and turn to on untill security light goes out 5 remove key and insert second key and repeat step 4 remove key and activate remote start now the led should go out but it doent it flashes once then stays solid any ideas as to why it wont program.i have check and rechecked and checked again with my wiring and all looks ok even had some one else go over it and they cant see anything wrong

0

Car won't start. Accessory mode turns on but not run mode and only with valid key

I have my Evo-All hooked up to a 2011 Taurus with PTS. If I do the 3x lock start then it will go through the lock unlock lock routine (I set that) and it will attempt to turn the ignition on. It will come up and say no key detected, but if I have the key in range (like I am sitting in the car with the key) and do the 3x lock it will turn the ignition on to accessory mode, but not run mode and it will not start the car. It does activate the brake light and the relays can be heard clicking. The guide told me to hook up to a wire that was not in the connector specified but if I use an earlier guide (given to me by the troubleshooting page) it shows a different wire in another connector that my car does have. Here is a link to my previous thread that describes it more: https://fortin.ca/en/qa/56883/2011-taurus-push-to-start-what-do-i-need?show=56883#q56883 EDIT: I didn't change anything, but now when I plug in the white 20 pin connector it will turn the car on provided that I have the key handy... Also, unlike before, now it does not turn the ignition to any mode. If I do the 3x lock and when it turns the brake lights on if I hit my start button it will start the car without me hitting the brake. I don't know what else to do

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer