Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

Need to re and have no more flashes left Service # 001A06609740

0

Decriptor limit

I need to reset flash limit on decriptor. Said reached limit for car. I havent reached any limit. How do I get it reset? My s/n 001A07338367

0

Flashlink updater 4 with viper

I have a Flashlink 4 Updater running current firmwear. I am trying to program an evo all module. When I am going through the steps in the Flashlink Manager and get to protocall Viper isnt an option. Can I not use an evo all with a viper 4806v?

0

INT-SL+ won't program to 2000 Silverado or be discovered by Flashlink Manager

I have a Fortin INT-SL+. HW Ver 2 Firmware Ver 3.01 mfg date 04/2018 Service number 002102061867 I also purchased a Fortin flashlink-lite updater I have a 2000 Chevy Silverado with an older Chrime Stoppers remote start, and had on omega IB-GMBP.DB-PAS-23A Passkey override. The omega unit went bad and appears to be discontinued. I purchaesd the Fortin unit to replace it. I just need the passkey function of the Fortin. Wired it in configuration 5 without data link. When I follow the programming instructions, the red light will come on, but not start blinking when the key is switched on. I have checked my wiring. I'm pretty sure I have it right. The red light also does not go out after I start the engine. I read on this forum that GM trucks can be particularly hard to program and that there is a firmware version 3.06 that resolves the issue. I bought the Fortin flashlink-lite updater to upgrade my firmware from 3.01 to 3.06 The flashlink-lite updater seems to be working with my laptop correctly. The Flashlink manager 4 shows the flashlink-lite updater as connected. When I plug in my INT-SL+ the red light comes on for a few seconds and goes out. Flashlink Manager4 always shows the "module status" as disconnected. I tried holding the INT-SL programming button before plugging the INT-SL into the Flashlink-lite. The red light stays on but the "module status" doesn't change. I have seen youtube videos that show the Fortin modules connecting almost instantly when plugged into the Flashlink devices, so I think something is wrong. I suspect the INT-SL I don't want to buy more stuff until I'm sure that I'm going to solve the problem. I feel that I should troubleshoot the connection between INT-SL+ and Flashlink first, since those are Fortin factory connections. That eleminates my wiring as a potential issue in the flowchart. Is there a way to tell if the INT-SL+ is bad?

0

Flashlink manager is stuck on 70% currently loading questions...did i install something wrong

0

Will the EVO-GMT4 work on a 2010 Silverado without AP8 code?

Will the EVO-GMT4 work on a 2010 Silverado without AP8 code?

1

If the Flash-Link Updater does not recognize my module, is the module defective?

I just bought a brand new EVO-ALL and Flash-Link Updater 2. I followed the instructions exactly on the Flash-Link Updater manual in order to get the latest updates for my device prior to install. The Flash-Link powers on and lights up red but the module never lights up and the Flash-Link light does not come on showing a link to the module. Any option I attempt to choose results in a message that the device was not found. Is this brand new module defective? Is there any other way to test it or reset it? Thanks!

1

If the Flash-Link Updater does not recognize my module, is the module defective?

I just bought a brand new EVO-ALL and Flash-Link Updater 2. I followed the instructions exactly on the Flash-Link Updater manual in order to get the latest updates for my device prior to install. The Flash-Link powers on and lights up red but the module never lights up and the Flash-Link light does not come on showing a link to the module. Any option I attempt to choose results in a message that the device was not found. Is this brand new module defective? Is there any other way to test it or reset it? Thanks!

1

If the Flash-Link Updater does not recognize my module, is the module defective?

I just bought a brand new EVO-ALL and Flash-Link Updater 2. I followed the instructions exactly on the Flash-Link Updater manual in order to get the latest updates for my device prior to install. The Flash-Link powers on and lights up red but the module never lights up and the Flash-Link light does not come on showing a link to the module. Any option I attempt to choose results in a message that the device was not found. Is this brand new module defective? Is there any other way to test it or reset it? Thanks!

1

Chevrolet Camaro Evo All with THAR

Will I need the flashlink updater to update and program the evo-all to remote start my 2012 Chevrolet Camaro 2LS?

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer