English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

16/03/2023

 Audi Costa Psichoulis (130Pts.)

0

2014 AUDI RS5. EVO ALL Remote start works oem fob 3X lock, but will not remote stop the vehicle with OEM FOB

Hi. I've just installed an EVO all with T-harness in standalone mode into my 2014 Audi RS5. Car has PTS and keyport. Everything went without a hitch, with decryptor programming, 3x lock oem keyfob, and works as intended, however I cannot remote shut down the vehicle with 3x lock oem FOB. FOB works to lock and unlock doors while remote started. I've checked flashlink to see if I missed selecting an option but there is nothing that mentions "remote stop" or related. Have I missed something, or is this par for the course for B8.5 Audi vehicles? Thanks. EDIT: I managed to remote shut down. I had to press the lock button on the OEM FOB about five-six times in rapid succession, but it works.
Connectez-vous pour répondre Voir 1 réponse(s)

15/03/2022

 Audi Christopher Edgett (210Pts.)

0

4x Lock Required to start Audi 2012 S4 with EVO-ALL+THAR-AUD1

2012 Audi S4 with Push button start, automatic trans, Installed EVO-ALL+THAR AUD1. (latest firmware confirmed with flashlink)

If the canbus is alive, the car will start on 3x lock of oem fob.

If the car is asleep, as in it sits overnight then "4x" lock is required to start the engine.

Something I've also noticed is 3x lock does not stop the engine when it has been started by the EVO-ALL module..so if engine is started with fortin module, no amount of fob lock button pressed will not stop the engine.

The system was updated with flashlink during the install process and only setting changed was the start run time length from 5mins to 30mins.

All the wiring that is required with the THAR-AUD1 has ben double checked and as mentioend, if canbus is live it'll start perfectly fine on 3x lock, it's just when the vehcle is asleep it's like you need to press the remote 1x to wake up the canbus and then 3x to start the engine. 

The 3x lock to shut off engine after start with fortin system, I'm not sure if this is possible or correct so I'm not 100% this is a concern.

Is any of the above normal operation?

Connectez-vous pour répondre Voir 1 réponse(s)

10/02/2022

 Audi Jeremy Petersen (130Pts.)

0

Brake command not shutting off the vehicle

When I get into the car and less the brake, the vehicle stays running. I can also drive away without putting the key into the Keyport. 2009 Audi A4
Connectez-vous pour répondre Voir 2 réponse(s)

10/02/2022

 Audi Jeremy Petersen (130Pts.)

0

Brake command not shutting off the vehicle

When I get into the car and less the brake, the vehicle stays running. I can also drive away without putting the key into the Keyport. 2009 Audi A4
Connectez-vous pour répondre Voir 2 réponse(s)

01/12/2021

 Audi Mark Wiggles (130Pts.)

0

2018 Audi Q3 Engine does not start, only accessories come on

The engine does not start, only the accessories come on and then after a few seconds everything turns back off when I push the OEM remote lock button 3x. Is there something I am missing? 2018 Audi A3 using Evo-All with THAR-VW1 Harness. Firmware: 67.04
Connectez-vous pour répondre Voir 1 réponse(s)

05/11/2021

 Audi phap truong (250Pts.)

0

2014 Audi RS7

What diode voltage do I need for the remote start installation?
Connectez-vous pour répondre Voir 1 réponse(s)

12/10/2021

 Audi Wesley Johnson (130Pts.)

0

Audi Q5 EVO-ALL Standalone worked initially then stopped

I just finished installing the EVO-All in standalone on my 2013 Q5 keyport with t harness. Tested the 3X lock a few times and it worked but now it does nothing. Also I installed the MPC SMartphone control with it and having the same issue. It worked on my phone a few times and now does nothing.
Connectez-vous pour répondre Voir 1 réponse(s)

19/01/2021

 Audi Marius Gheorghe (130Pts.)

0

Dcryptor's limit has been reached for this car 2014 Audi sq5

Hi, I need help with my EVO-AUDT1 I have it installed about a month ago, everything worked but not ok. Most of the time remote start won't work or at least not at the first try. Needs a couple of tries, lock, unlock and will eventually start. Today I had some time so I decided to remove the unit and change the settings (at the customer service recommendation to try the LOCK/UNLOCK/LOCK instead of what I initially had LOCK/LOCK/LOCK FOR REMOTE START). I did the settings change and installed back the module, the car will remote start much better than before (still failed a couple attempts but most of the time worked fine) however sometimes after shutting off engine and close the door the car will start! Just like that, after pushing ONE TIME ONLY the door lock button car will start. So I decided to revers the setting to what I initially had ( 3 x LOCK fosr remote start) at least this way the car won't start when simply lock. And from here programming issues begin : I was not able to have the remote starting working again. I fallowed the same programming procedure like before, on the computer everything seems to be fine but when connecting the module nothing, car won't remote start at all. I tried a couple of times step 1 for DCRYPTOR , ever time worked fine, but on the car won't start. I also tried and flashed not the recommended firmware version but the lattes one compatible for this module , (the 70) and repeat all the steps, still nothing. I eventually went back and flash the same version that I initially had ( the 60.08) and did the recommended settings, no change at all, with 3 x LOCK for remote start, fallowed successfully all the programing steps and nothing, car won't remote start. While I was doing the last try when I was running the dcryptor, I got the message of dcryptor limit have been reached for this car! I tried to reconnect the module and fallow the procedure for STEP 1 and nothing. Same message. Nevertheless, this is getting pretty frustrating... Also, the module I received shows manufacturing date beeing sometimes in 2018 and for my vehicle shows that compatible modules needs to be manufactured 2019 and up. I called customer service when I received the module and I have been told it doesn’t matter, will still work. And it did, but with the described issues, so I wonder if that may be the initial issue why car won't remote start as it should to begin with? How do I reset dcryptor's limit? And what could be the issue that car won't remote start even if the programing seems to be successful? I am pretty sure every time the connectors were well plugged * After talking with customer service this will be solved by sending a e-mail with the unit s/n for reset.
Connectez-vous pour répondre Voir 0 réponse(s)

13/01/2020

 Audi Sean (750Pts.)

2

After remote start can press brake and drive vehicle for remote start run time without key

2013 Audi q5 with Keyport and no push to start Evo all module with t harness. Works flawlessly otherwise latest firmware is 60.08 but install guide says 60.02. I assume it's just a matter of pulling the module back out and selecting an option I just don't know which one.
Connectez-vous pour répondre Voir 2 réponse(s)

23/11/2020

 Audi Travis Ryan (130Pts.)

0

2014 Audi SQ5 problem with key programming

I am trying to get the Evo-All with the AUDT1 to work in my 2014 SQ5. The problem is during programing. I get to the point of all 3 lights flashing, then solid red, then I get flashing red every 1 second instead of red and yellow flashing. I put a new battery in the remote, and tried again. The second time, I got the red and yellow flashing, so I did the Decrypt. I was able to activate the Autostart with 3 lock butttons, but the car won't start without putting the key in the keyport. I get a red light, then a click and yellow light, then a red light. Then a red blink 3 times. The car doesn't start, so the 3 red is no tach signal, which makes sense. If I put the spare key in the keyport, then press 3 locks, the car starts right up. I think the decrypt didn't work. I tried a master reset, and retry configuration, but now I can't get the red and yellow again. I have tried 5 times, and can't get a key read off the keyport. iI have connected the t cable to the keyport, the brake cable, and the 2 canbus wires to the steering column can bus wires. When the EVO-ALL is trying to read the key, the car will show a Parking Brake Malfunction, the HVAC turns off and back on, then gives another Parking Brake Malfunction, then shows a red light, then a flashing red light. Not sure why the controller won't program correctly. Does anyone have any ideas?
Connectez-vous pour répondre Voir 1 réponse(s)

09/10/2020

 Audi Shawn sri (460Pts.)

0

2012 q5 evo all question

Hi, I just installed a evo all stand alone on a 2012 q5 with the t harness, everything works perfectly but does anyone know if the keyport is supposed to lock the key in? now I can start the car and take the key in and out, and also the car does not shut down when pressing the brake before inserting the key in the keyport thanks
Connectez-vous pour répondre Voir 1 réponse(s)

27/04/2020

 Audi CRAIG HANBY (130Pts.)

0

Audi A4 2009 TDI KEYPORT REMOTE START PROBLEM

Remote start not working. 
Checked the following options - 

    Bypass C1 - D6 - D2 Remote starter - 32.6 - 34.3 - 38.2

The unit connects fine, it starts via keyport, decryptor runs fine, when I press the lock button the EVO One flashes, it also flashes when I unlock. Unfortunatley when I press lock x3 it doesnt remote start.

 

Using T Harness

 

Completed the wiring, +12v red, Yellow to Clutch, Grey to can orange green, grey black to can orange brown, black to GND, key port connector, red connector, white connector and the evo one loop connector.
 

Connectez-vous pour répondre Voir 1 réponse(s)

14/03/2020

 Audi Phillip Owen (130Pts.)

0

Do I choose key port or TDI?

I don't know which one to choose on the Q5 the key port or the TDI? Also does the $99 remote start come with the T-harness need for install?
Connectez-vous pour répondre Voir 1 réponse(s)

05/03/2020

 Audi Stuart Pullen (190Pts.)

0

2009 S4 MANUAL TRANS, NO START AFTER 3X LOCK

Hello, I have a manual trans Audi s4 2009 keyport Evo One , i have installed the T-harness - yellow line from 6 pin to the clutch bypass (red/blk) in engine bay as per pics, Canbus High and Low installed correctly and the Pink from the 6 pin to the purple/ yellow to convenient ignition out. I have the module programmed as per intructions and no error. when connect all the plugs and lock the car then try 3x lock to RS nothing happens. I see the module flash with a blue led at every lock and unlock but no ignition. Evo One S/N 002B04 013291 Thank you in advance! Stu.
Connectez-vous pour répondre Voir 1 réponse(s)

07/02/2020

 Audi SAMEER SEHRAWAT (160Pts.)

0

evo all not even starting the ignition audi a4 2011 automatic

i tried everything and evo all wont start my car, i can hear clicks in the dashboard but no ignition lights and finally after 6,7 sconds the car gets unlocked instead of starting.
Connectez-vous pour répondre Voir 1 réponse(s)

13/01/2020

 Audi Sean (750Pts.)

2

After remote start can press brake and drive vehicle for remote start run time without key

2013 Audi q5 with Keyport and no push to start Evo all module with t harness. Works flawlessly otherwise latest firmware is 60.08 but install guide says 60.02. I assume it's just a matter of pulling the module back out and selecting an option I just don't know which one.
Connectez-vous pour répondre Voir 2 réponse(s)

15/12/2019

 Audi Joe Vislocky (130Pts.)

0

I need to know everything I need to install EVO-ALL in 2016 Audi Q5 with key port?

Do I need the flash link updater? I didn't when I installed a unit in an Infinti EX-35.
Connectez-vous pour répondre Voir 1 réponse(s)

20/02/2019

 Audi Grease Monkey Tuners (1230Pts.)

0

2009 - 2014 Audi S4 Parking/Marker Light

Hey Fellas, I installed an EVO-ALL w/ AUD1 T-Harness on a 2011 Audi S4 as standalone using Guide # 77161. Remote starter works great but park lights don't turn on when its running. I had the parking light control ON the settings/options using through the flash-link updater and I don't see an analog wire to actually connect the EVO-ALL/EVO-ONE into vehicle's parking light circuit. Am i missing anything? Thanks!
Connectez-vous pour répondre Voir 2 réponse(s)

20/02/2019

 Audi Grease Monkey Tuners (1230Pts.)

0

2009 - 2014 Audi S4 Parking/Marker Light

Hey Fellas, I installed an EVO-ALL w/ AUD1 T-Harness on a 2011 Audi S4 as standalone using Guide # 77161. Remote starter works great but park lights don't turn on when its running. I had the parking light control ON the settings/options using through the flash-link updater and I don't see an analog wire to actually connect the EVO-ALL/EVO-ONE into vehicle's parking light circuit. Am i missing anything? Thanks!
Connectez-vous pour répondre Voir 2 réponse(s)

09/12/2018

 Audi Luc Ostiguy (940Pts.)

0

bcm unit in audi q5 2018

i don't find the bcm unit in the 2018 q5 technik
Connectez-vous pour répondre Voir 1 réponse(s)

07/10/2018

 Audi Ryan Biccum (130Pts.)

0

2012 q5 PTS with viper remote starter

I have a 2012 audi q5 with a pre installed viper remote starter. It functions correctly but I would like to ditch the viper fob and use the OEM for 3x lock start. Is there a fortin module that will recognize 3x lock and send a negative trigger signal to start via the viper unit?
Connectez-vous pour répondre Voir 1 réponse(s)

17/05/2018

 Audi Pauly_12v (210Pts.)

0

Evo All 2010 Audi S4

Hi, just installed an evo all into an 2010 S4 with PTS using the new transponder bypass installation guide. After decrypting the key and reconnecting the module, the vehicle started via 3x lock perfectly and performed take over, after the second test the vehicle kicked over then turned off and attempted a second restart without any success. After this the module doesn’t respond to 3x lock at all. Any ideas?? Module still has power and can activity thank you Paul Starter 7.1.16 evo 2.4.18 date 02 2016
Connectez-vous pour répondre Voir 1 réponse(s)

23/11/2016

 Audi Mohsen Bayati (130Pts.)

0

Evo all doesn't remote start the car

I have got an Evo all installed on a Audi A4 2012 PTS I think everything is connected correctly according to the guide. the car starts normaly but when I try to remote start it the yellow light goes on and the car does not start. The module should be programmed correctly as the blue LED started flashing rapidly after programming . could you please tell me what to check. I have installed it as stand alone installation with 3x lock option and no RF kit. Thanks Mohsen
Connectez-vous pour répondre Voir 1 réponse(s)

18/10/2016

 Audi Luc Ostiguy (940Pts.)

0

Manette Intelligente Audi 3X Lock remote start

Est-ce que je pourrai debarrer les porte en utilisant ma manette OEM ? ou devrais-je utiliser la cle proprement dit?

 

 

La télécommande d’origine du véhicule sera fonctionnelle pendant que

le véhicule est en marche, toutefois, le déverrouillage des portes par la

clé d’accès Intelligente ne sera pas fonctionnel.

Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer