Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

After install, will I still be able to use my OBD11 port like normal?

At the end of this month I'll be getting my Evo-All installed and I cannot wait! But quick question, since the T-Harness connects to the back of my OBD11 Port, after install can I still use the port to tune my Mustang? I have been data-logging with a company to get my custom tune just right, and I want to make sure I'll still be able to use the port to upload the file to my car? Thanks so much in advance!!

0

key port works but only when t harness is unplugged

2012 a4 w/push to start will not start. fortin inicated the key port has to be functional in order for it to start. but the key port does not work unless the t harness is unplugged. I was unable to get any help from fortin when i called anyone else had this issue and how can i resolve. the install thus far has been easy , simply tapped the brake signal wire and can high and can low. when the evo is connected it does attempt to start the car meaning it flashes each of the three lights but never hear the starter engadge. updated firmware as requested previously by fortin. but when i called today fortin tech was no so eager to assist. said either the evo relays are bad or the t harness is bad. can i help with anything else. I indicated i would like assistance tryin to resolve. so im trying to work through the troubleshooting he offered but now will not answer the phone. any help would be greatly appreciated.

0

Can not proceed Page 6/10 (dcryptor programming procedure). when i apply the step 4 in page 6/10 the Blue LED turns off

I've updated module Evo-One for my Audi A5 2011 Gas with key-port before the installation and now can not proceed Page 6/10 (dcryptor programming procedure). when i apply the step 4 in page 6/10 the Blue LED turns off which makes unable to continue the step 5.

0

After install, will I still be able to use my OBD11 port like normal?

At the end of this month I'll be getting my Evo-All installed and I cannot wait! But quick question, since the T-Harness connects to the back of my OBD11 Port, after install can I still use the port to tune my Mustang? I have been data-logging with a company to get my custom tune just right, and I want to make sure I'll still be able to use the port to upload the file to my car? Thanks so much in advance!!

0

After install, will I still be able to use my OBD11 port like normal?

At the end of this month I'll be getting my Evo-All installed and I cannot wait! But quick question, since the T-Harness connects to the back of my OBD11 Port, after install can I still use the port to tune my Mustang? I have been data-logging with a company to get my custom tune just right, and I want to make sure I'll still be able to use the port to upload the file to my car? Thanks so much in advance!!

1

3 pin shock sensor connector

What is the name of the type of connector used for the shock sensor port and where can I purchase a connector with a wiring harness? If I wanted to add a tilt sensor and wired the trigger into the pink/black wire (A15) would it give me a proper tilt alarm response if triggered on a two way remote or parking light flash upon disarm? I know I need to tie the trigger for the tilt alarm into zone 8 for that I just dont know where to do that. Are the ground and 12v leads coming from the shock sensor port only active when the alarm is armed or are the always active?

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer