English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

07/11/2021

 Ford Jesse Slone (130Pts.)

0

2008 Ford Expedition driver door pin wire location?

I am trying to locate the driver door pin wire on the driver's side.  I even cut a wire I was sure was it, only to find that the door chime still went off when I closed the door.  I obviously don't know how to test this correctly 

I tried disconnecting the two harnesses that are in the driver kick panel that are smaller, neither of them seemed to have any effect when disconnected them and closed the door, the chime still stopped.  So it must be in the large connector with the bolt through it, or somewhere else?

In the guide, its says "see diagram", but I can't find one in there to save my life.  I would prefer to stay on the Driver's side since I don't have any wire handy to fish over to the SJB.  Of course, at this point, I would take the SJB diagram, but can't find it.  Thanks for your help!

Connectez-vous pour répondre Voir 1 réponse(s)

29/03/2019

 Ford Nelson Santos (130Pts.)

0

Will the firmware for 2016 expedition standard key work for push to start?

Firmware compatible.
Connectez-vous pour répondre Voir 1 réponse(s)

21/03/2019

 Ford Geoffry LALAND (160Pts.)

0

What will work for a 2014 expedition

2014 expedition
Connectez-vous pour répondre Voir 1 réponse(s)

20/03/2019

 Ford Geoffry LALAND (160Pts.)

0

What is a standard key mean on a 2014 Expedition

What is a standard key
Connectez-vous pour répondre Voir 1 réponse(s)

14/03/2018

 Ford Chris Vaughan (130Pts.)

0

EVO One; after remote start vehicle will not shut down

I've installed two of these, within a month of each other. Both installs went smoothly. However, this last one is a 2007 Expedition. I can start it with the fob w/3x Lock, and kill it with the 3x Lock. But it is letting me drive the vehicle without the key and will not shut off with by pushing the brake, or with the key. After the full run time, it stops like normal. I have not tried driving it for 15 minutes, as i'm afraid it will shut down while driving. A1-A11 are active.
Connectez-vous pour répondre Voir 2 réponse(s)

14/03/2018

 Ford Chris Vaughan (130Pts.)

0

EVO One; after remote start vehicle will not shut down

I've installed two of these, within a month of each other. Both installs went smoothly. However, this last one is a 2007 Expedition. I can start it with the fob w/3x Lock, and kill it with the 3x Lock. But it is letting me drive the vehicle without the key and will not shut off with by pushing the brake, or with the key. After the full run time, it stops like normal. I have not tried driving it for 15 minutes, as i'm afraid it will shut down while driving. A1-A11 are active.
Connectez-vous pour répondre Voir 2 réponse(s)

13/10/2015

 Ford Orlan (210Pts.)

0

2014 Expedition lock, unlock, driver pin wire color / location.

Hello, I have a Pro-Start remote starter that will be connected to EVO-all using d2d. I will be using guide 3318, connection 4 as per guide. My question is where do i connect the lock , unlock and driver pin wires of EVO-all to the vehicle? The guide shows to connect the wires from evoall to pins 6,8,9 of the connector in the vehicle for lock/unlock/driver pin. However, slots 8 and 9 are empty and slot 6 is for factory alarm arm. As per Autostart wiring guide, lock is at pin 17, unlock at pin4 and driver pin at pin 14. Can you please clarify where to connect the lock/unlock/driver pin wires from evo-all to the vehicle? Also, the guide shows to connect the remote start ignition and evo-all keysense wires to the number 1 pin of the PATS module. The guide labeled it as Keysense. The vehicle wiring guide shows it is Pats Ignition and that the keysense wire of the vehicle is at the ignition harness (blue/gray). Do I go ahead and connect ignition and keysense wire as per evo-all guide? or should i connect to the wire specified in the vehicle wiring guide? Also, if the vehicle does not have factory alarm, do I still connect notes 1,2,3 (in green). How would i wire connector D (red 6 pin harness of evo-all) if there is no factory alarm? Last question, how do i know if the vehicle has 40-bit or 80-bit keys. Evo-all guide only lists 2014 expedition as 80 bit however, other bypass modules (idatalink) lists this vehicle as 40 bit key. Can you please advise? Thank you in advance.
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer