English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

24/02/2017

 Nissan Keith Sawmiller (130Pts.)

0

2011 Nissan Pathfinder - No Start w/o Key - Start then Killed w/ Key in Barrel

Fortin EVO-ONE w/ T-Harness. Regular (non-intel key) Summary: 1) I am trying to determine why I only get cranking & starting when the key is in the barrel 2) I suspect I'm not getting or decoding CAN data in the EVO-ONE. Details: I have installed the unit and, updated both bypass and remote start firmware via flashlink. I've also set the following options in remote start: 32.3, 2.3, 8.2. My first issue appeared when pairing the RF remote kit (RF442W). I had to manually apply +12V to the black (foot pedal brake) wire after 5 button presses in order to enter the "add remote" option. I thought brake status came over CAN bus. After issuing a remote start command, the red light on the Fortin comes on, the dash lights up, and hear relays clicking in the engine bay but no cranking. It fails after two attemps and flashes the 4x light code = no tack feedback. Same result with GWR wire grounded. If I put the key in the ignition barrel and re-attempt the test, this time the vehicle starts, but then shuts down after 3 seconds with the same no tachometer feedback error code. If I change the tachometer setting via flashlink (20.4), the vehicle will stay running. I have tried 20.1, 20.4, 20.5, 20.6 I pulled out my 2CH oscilloscope and probed the CAN pins (6 & 14). There is clearly data on the bus, though the CAN L signal has significantly higher capacitance (signal does not have hard edges like CAN H). According to the install guide, doors/trunk/brake/tach/etc should be coming into the EVO-ONE via CAN bus. I'm worried that I either have a fortin or vehicle CAN bus problem. For what it's worth, I disconnected the CAN bus wires into the EVO-ONE and got the same result. Additionally, I suspect there is another reason as to why I don't get cranking without the key in the barrel. Any additional steps or guidance appreciated.
Connectez-vous pour répondre Voir 1 réponse(s)

23/11/2016

 Nissan Daniel Waslenko (2650Pts.)

0

How to hook up auto light shutdown on 2011 Nissan Pathfinder with Intel key

I am using an EVO-ONE. I hooked the Dark blue from pin A8 to the driver door pin listed on wirecolor as the gray wire at pin 7 on the BCM in the white 15 pin plug. If that wire is hooked up the vehicle starts, then immediately shuts off. I left it disconnected until the customer comes back this Sunday so I can try to figure out what is going on. Remote start operates fine with it disconnected, but the lights do not shut off which will cause battery issues. I do not have the service number on hand. How do I hook up the wire to shut off the autolights? Is it possible that the gray is the wrong wire? Also on the wirecolor site it says the autolight shutdown wire is purple at the parking light harness but it is supposed to be cut. The install guide says to hook it up to the door pin.
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer