Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

User

tjamz0061

Joined on the:

Jul. 21, 2011

Score

340

Comment(s)

1

Voted question(s)

0

Voted answer(s)

0

Votes up

0

Votes down

0

Votes up received

2

Votes down received

0

Recent Activity

Question(s) asked

4

Answered question(s)

1

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question
RECENT ACTIVITY QUESTION(S) ASKED ANSWERED QUESTION(S) COMMENTED QUESTION(S)

20/09/2020

 Toyota tjamz0061 (340Pts.)

0

09 Rav4 PTS EvoOne will not program

So I completed the installation as specified here: https://cdn02.fortin.ca/en/download/24101/24101.pdf When I go through the programming procedure everything works until I get to step 4. The blue light goes out as indicated, but it never flashes or comes on solid so it never completes it's programming. Any suggestions appreciated! I've tried reversing the CAN wires.
Login to reply View 1 answer(s)

11/02/2018

 Subaru tjamz0061 (340Pts.)

0

2018 Subaru Outback Keystart EVO-ALL Solace S3 (IC4) Won't Stay Running

Just installed a Solace S3 remote starter (IC4 module w/ relay pack v. FW51) using an EVO-ALL in my 2018 Outback with a standard key start. Everything went well. Flashed with 79.45 firmware, did the programming, DCryptor went well also. Car will lock/unlock/hatch release no problem. Tach is programmed via data. Vehicle will start, run for just a couple seconds and shut off. It will attempt this 3 times. The remote says that the car is running (I get confirmation as such) but it still dies.... then attemps restart. I've double checked all wires at ignition. All appears good. Any ideas?
Login to reply View 1 answer(s)

29/12/2014

 Nissan tjamz (300Pts.)

1

2012 Nissan Armada Smartkey won't stay running

Recently installed a remote start for a customer in a 2012 Nissan Armada. Unfortunately the vehicle is 200 miles away and won't be able to be in the shop until this Sunday (when tech support is closed). I don't have the service number on the EVO-ALL but am 100000% positive that I am using the right firmware and that all connections are proper. When the vehicle left the shop it was working 100% perfectly, however after a day of use the customer noticed that the vehicle would start for only 3 seconds before shutting off. It was long enough that the remote starter saw the tach signal and assumed the vehicle was still running as it was still counting down the timer on the fob, so I'm ruling out starter issue (for now). Does anyone have any other ideas/thoughts on what could be causing this? Would a GWR wire cause this? Is it possible it lost it's transponder programming?
Login to reply View 1 answer(s)

28/12/2014

 Pontiac tjamz0061 (340Pts.)

1

08 Pontiac Torrent Won't program

So I'm attempting to install an EVO-ALL along with an Ultrastart 3295 remote start. Firmware Version 70.16 When I go to program the blue light goes out and never starts flashing when I get to step #4. At first I noticed the car wouldn't start this way either. Ultimately I determined it was because there wasn't power passing through the White Green wire on connector D to the White Red wire on connector D so I unhooked the entire remote start & bypass module and jumpered the two wires together to verify the car would start that way (it did). Next I reconnected the starter and bypass and removed the jumper that I had temporarily installed and tried programming again... same issue. Anyone have any suggestions?
Login to reply View 1 answer(s)

15/12/2014

 Ford tjamz0061 (340Pts.)

1

EDIT: New Problem 11 Taurus Regular Key Phantom hood & brake fault

NEW PROBLEM: Vehicle will run for a couple of seconds (15 maybe) and then shut down.... grrrr.... Any advice is welcome While attempting installation on a 2011 Taurus (standard key) I encountered a situation where I was getting phantom hood & brake faults one the remote starter (One-Start OS380). Ultimately I was able to remedy the solution by deactivating those functions of the EVO-FORT1 and hardwiring to the vehicle. I guess this isn't a question really other than to ask if others have had similar issues and what they did to remedy the situation.
Login to reply View 1 answer(s)

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue