Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

28/12/2014

 Pontiac tjamz0061 (340Pts.)

1

08 Pontiac Torrent Won't program

So I'm attempting to install an EVO-ALL along with an Ultrastart 3295 remote start. Firmware Version 70.16 When I go to program the blue light goes out and never starts flashing when I get to step #4. At first I noticed the car wouldn't start this way either. Ultimately I determined it was because there wasn't power passing through the White Green wire on connector D to the White Red wire on connector D so I unhooked the entire remote start & bypass module and jumpered the two wires together to verify the car would start that way (it did). Next I reconnected the starter and bypass and removed the jumper that I had temporarily installed and tried programming again... same issue. Anyone have any suggestions?
Login to reply View 1 answer(s)

26/08/2014

 Nissan Jesse Hir (680Pts.)

2

Murano shuts down

I've installed 2 remote starters in 14 Murano's and both have the same problem. Once in a while the vehicle starts and shuts down right away. If you start it again it starts fine. Firmware is 72.14 UltraStart 3295 2 way remote starter Nissan T-harness used Option B2 turned on
Login to reply View 1 answer(s)

18/12/2013

 Chevrolet tjamz (300Pts.)

0

Programming issue 2010 Colorado

Alright. Since the tech support number is busy again I'll try on here. 2010 Colorado installing an Ultrastart 3295. I've double and triple checked the connections to ensure I'm on the proper wires but it absolutely will not program properly (wiring style 8 program style 3). Steps 1 & 2 work (pretty hard to mess them up) but step 3 when I turn ignition to the on/run position the Blue LED turns off (so far so good), the Red LED turns on (also so far so good) but then the red LED never flashes, the blue one does however. I've tried just going to the next step (start and hold crank for 3 seconds) but the yellow LED never comes on to signal programming is complete. FWIW, this is a very stripped down version of the colorado (work truck basically) w/ no power locks/windows/etc. Chuck
Login to reply View 1 answer(s)

11/11/2013

 Jeep Jesse Hir (680Pts.)

2

2003 Jeep Liberty runs 2 seconds then dies

I used a UltraStart 3295 with an EvoAll in a 03 Liberty. The vehicle started by remote start once and stayed running, every time after the vehicle will start for 2 seconds then dies. Wired in as per instruction for evo-all (connection 1, program 1). Flashed evo-all as per instructions to 4.06. Turned on D2D in options tab. The door locks also are not working through remote starter. The horn honks 5 times after each start fail.
Login to reply View 1 answer(s)

13/11/2013

 Acura Jesse Hir (680Pts.)

2

10 Acura RDX Door Locks won't unlock if running unless you lock first

Using Evo-All with Ultra Start 3295 2way wired D2D. Vehicle is set to unlock doors, start vehicle, and lock doors--set through evo-all. Most current update in evo-all. If remote started, the doors unlock, vehicle starts, doors lock.==Perfect Problem is when customer comes to vehicle and pushes unlock on remote starter remote the doors will NOT unlock unless you push the lock button first.(even though the doors are locked at start up) Seems like something in the settings must be wrong but what??
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue