Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

User

Josh Hunt

Joined on the:

Jul. 3, 2017

Score

130

Comment(s)

1

Voted question(s)

0

Voted answer(s)

0

Votes up

0

Votes down

0

Votes up received

0

Votes down received

0

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

0

EVO One only shows yellow light on ignition on, wont remote start

I have a Nissan Xterra 2007, I purchased a EVO One with T-Harness and RF642W RF Kit. I'm using install guide 33131 for EVO one. I wired per instructions with A1,A2,A3,A8,A15 | E harnes by T-Harness, C3,C4, and D6,D4. D1 & D3 do not plug into anything and have been set aside. Held down Bypass Prog Button when inserting 6-pin power plug. I let LED cylce through once and waited for blue light and release bypass prog button and pluged in 20-pin, 6-pin bypass relay, 5-pin can bus, and 4-pin data link ant while the light stayed blue. I insert key into ignition chamber and turn to ON. Blue goes off then flashed blue. I turn key to off. Programming should be complete. 3X lock on OEM remote does not remote start. I insert key into ignition and turn to ON and the EVO One lights up yellow. I use the flashlink to update bypass to 72.27 and the remote start to 1.21. In bypass I enable C1 & D2. EVO still does the same thing when pluged into vehicle. I try using programming button but holding it down for 1+ minute with no horn beep. I suspect wiring was not correct. I double checked and have CAN-high and CAN-low correct. A1 is on (+) ignition (Pink-E5). A2 & A3 are on wiring diagram pin 14 & 13 but on vehicle BCS/BCM manual terminal is 8 & 7. A8 did not corispond with Wirecolor.com picture, image shows incorrect junction terminals for US version of Xterra. voltmetered 4 different plugs and no luck. According to vehicle BCS/BCM manual, driver door command is a Gray wire at M19 harness pin 47 next to 40-pin harness. When locking and unlocking the EVO one does not light up. I can't tell if OEM alarm is being set by Cars BCS/BCM or if it by the EVO One but the alarm does activate on door trip. Remote Start Programming: 2.3 | 3 (1) | 4.1 | 6.3 | 7.1 | 8.2 | 9.1 | 11.1 &11.4 | 12.1 | 13.2 | 14.2 | 15.2 | 16.5 | 18.1 | 19.1| 20.1 | 21.1 | 24.1 | 25.1 | 26.1 | 29.1 | 30.1 | 31.1 | 32.3 | 33.1 | 34-OFF-OFF| 35.1 | 36.2 | 37.1 | 38.1 (38.3-Off) | 39.1 Bypass Programming: A1-A11 - ON | B1-OFF| C1-ON| D2-ON| D3-D6 -OFF Unit Options : D.1 | D1.6 | H1 are enabled. I have master reset both side of EVO-One and started fresh with first paragraph and no luck, just same results. Any thoughts on where to look for the issue. I can grab field mesurements if desired.

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue