Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

07/10/2023

 Mazda William Roberts (130Pts.)

-1

Evo One, 2021 Mazda CX5 automatic, not getting blue led on step 4

It is set up on bypass firmware 85.12 and remote start firmware 1.26. I reflashed each firmware to the module in pro mode just be sure then reflashed the settings. It is set to the defaults with the wizard but I did switch to pro mode at one point to verify a few of the settings that were mentioned in the guide, A11 C1 and D2. Once I bring it to the car and plug in holding the button, blue led comes on and then I plug in 3 other cables (THAR-ONE-MAZ3 cable). I press ignition twice, it just cycles through the leds over and over. I've waited at least 2 minutes and it never stops cycling. I tried to read the voltage on the CAN BUS and it was 0.8-1.3V DC while this was going on. Any other things I can try to get the Dcrypt done? Thank you!
Login to reply View 1 answer(s)

19/08/2021

 Mazda Michael Jover (180Pts.)

0

2014 Mazda CX5 Manual - Installed EVO-ONE W/ THAR Lights blink blue does not stay on solid

Hello, I purchased an EVO-ONE kit along with the T-harness for my 2014 Mazda CX5 manual trans, push button start. I programmed the module originally with the Flash Link on windows 10 laptop, I installed it in the vehcle with the T Harness. I ran a wire for the hood switch and mounted it. I am unsure if I hooked up the clutch switch correctly, the picture shows it in series but the input goes straight into the module and then back around into the T Harness..I hooked it up to the ground side trigger. The module will not power up and stay on, if I hold the programming button or unplug the 6 pin and plug it back in the unit will blink all the LEDs and then they just all go out. The blue one will not stay on. Can I get some guidance guys? Anybody run into this before? I double checked all the plugs into the module, the T Harness plugs. Mike
Login to reply View 3 answer(s)

19/08/2021

 Mazda Michael Jover (180Pts.)

0

2014 Mazda CX5 Manual - Installed EVO-ONE W/ THAR Lights blink blue does not stay on solid

Hello, I purchased an EVO-ONE kit along with the T-harness for my 2014 Mazda CX5 manual trans, push button start. I programmed the module originally with the Flash Link on windows 10 laptop, I installed it in the vehcle with the T Harness. I ran a wire for the hood switch and mounted it. I am unsure if I hooked up the clutch switch correctly, the picture shows it in series but the input goes straight into the module and then back around into the T Harness..I hooked it up to the ground side trigger. The module will not power up and stay on, if I hold the programming button or unplug the 6 pin and plug it back in the unit will blink all the LEDs and then they just all go out. The blue one will not stay on. Can I get some guidance guys? Anybody run into this before? I double checked all the plugs into the module, the T Harness plugs. Mike
Login to reply View 3 answer(s)

19/08/2021

 Mazda Michael Jover (180Pts.)

0

2014 Mazda CX5 Manual - Installed EVO-ONE W/ THAR Lights blink blue does not stay on solid

Hello, I purchased an EVO-ONE kit along with the T-harness for my 2014 Mazda CX5 manual trans, push button start. I programmed the module originally with the Flash Link on windows 10 laptop, I installed it in the vehcle with the T Harness. I ran a wire for the hood switch and mounted it. I am unsure if I hooked up the clutch switch correctly, the picture shows it in series but the input goes straight into the module and then back around into the T Harness..I hooked it up to the ground side trigger. The module will not power up and stay on, if I hold the programming button or unplug the 6 pin and plug it back in the unit will blink all the LEDs and then they just all go out. The blue one will not stay on. Can I get some guidance guys? Anybody run into this before? I double checked all the plugs into the module, the T Harness plugs. Mike
Login to reply View 3 answer(s)

19/08/2021

 Mazda Michael Jover (180Pts.)

0

2014 Mazda CX5 Manual - Installed EVO-ONE W/ THAR Lights blink blue does not stay on solid

Hello, I purchased an EVO-ONE kit along with the T-harness for my 2014 Mazda CX5 manual trans, push button start. I programmed the module originally with the Flash Link on windows 10 laptop, I installed it in the vehcle with the T Harness. I ran a wire for the hood switch and mounted it. I am unsure if I hooked up the clutch switch correctly, the picture shows it in series but the input goes straight into the module and then back around into the T Harness..I hooked it up to the ground side trigger. The module will not power up and stay on, if I hold the programming button or unplug the 6 pin and plug it back in the unit will blink all the LEDs and then they just all go out. The blue one will not stay on. Can I get some guidance guys? Anybody run into this before? I double checked all the plugs into the module, the T Harness plugs. Mike
Login to reply View 3 answer(s)

11/01/2020

 Mazda Alex Macharia (130Pts.)

0

Mazda Failing Decryption process (not able to get a solid blue)

I have tried to run the exact process for initializing decryptor for a CX-9 install, starting with diconnecting the neg battery terminal and then connecting the steering wheel white terminals into the T harness,reconnecting battery power and then holding down the button on the Evo one module while plugging in the 6 pin connector. I have not been able to get the module to set the blue solid light. Anyone run into this? Module was programmed correctly via flashlink
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue