Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

03/12/2024

 Mazda Kong Vang (250Pts.)

0

2013 CX-5 Cranks But Won't Start M/T

EVO-ONE. I have the THAR-ONE-MAZ3 harness. White cable for clutch bypass is connected. Not sure what's going on. I've tried changing the programmable output from 2.1 (default) to 2.2 (I think it should be this one?) and still no luck. It will try to crank for a few seconds, then shut off then tries again for a few seconds but won't start. Yellow jumper was cut when I received it, but it is currently twisted together until I verify what the issue is then I'll do a more rigid connection. I don't have the hood pin switch connected, my kit didn't come with it. Not sure if this is preventing it from starting or not. I have tried enabling and disabling A11 for this but still no luck with remote start. SN: 002B04 643579
Login to reply View 1 answer(s)

10/02/2024

 Mazda Kevin Hunt (130Pts.)

0

Manual CX-5 Crank no start

2014 Mazda CX5 ; manual push to start ; Evo-one w/MAZ THAR ; SN 002b04 638289

Cranks but doesn't start. All fob functions work, car runs normally, and it goes into ready mode and shuts down after exiting. Won't autostart after getting out of the vehicle - what am I missing? Valet mode off.

Using default settings with the plug&play harness.

Firmware 85.14

A1 through A-10 : ON

A11 OFF ; B1 OFF ; C1 ON

D2 ON

D3-D5 : OFF ; D6 ON

Firmware 1.26

2 through 15 : option 1 (default)

16.5 ; 18.1 ; 19.1 ; 20.8 ; 21.2 ; 24.1 ; 25 (off) ; 26.1 ; 29.1 ; 30.1 ; 31.1 ; 32.1 ; 33.2 ; 34.1 ; 35.1 36.3 ; 37.1 ; 38.1 ; 39.1

Login to reply View 1 answer(s)

29/07/2023

 Mazda Richard Arms (130Pts.)

0

2019 Miata manual, crank but no start. Getting three flashes after failed attempt.

Evo-one 002B04310069
Login to reply View 1 answer(s)

08/01/2023

 Mazda moosespectacles (160Pts.)

0

(15 Mazda 3) Car cranks but ignition does not turn on, after steps 1-12

I can get through steps 1-12 (though the security light never displays on the dash), and when the ignition is supposed to turn the car on, the dash lights turn on, I hear a crank, but the car never starts. However, I do get the red and yellow lights flashing, so I tried connecting to the PC to use dcryptor, thinking maybe it will turn on after, but still no luck. Does anyone know what the issue is? I'm using THAR-MAZ1 with the Evo-All and following guide 62681. Everything is plugged in, and the only wiring done is the Lt blue to Lt blue on the 32 pin connector, and the Lt Blue/Black to the red on the 32 pin connector. Am I missing a connection, perhaps an ignition wire? Any help will be greatly appreciated. Thank you in advance.
Login to reply View 0 answer(s)

11/03/2022

 Mazda Rohaan Arshad (160Pts.)

0

'21 Manual Miata cranks, but doesn't start

I own a 2021 Mazda MX5 Miata RF GT in a manual transmission. I'm using the EVO-ONE with the THAR-ONE-MAZ3 T-Harness. I've made sure to splice the white cable (Manual only) with the corresponding white pin A5 on the 20 pin connector for the clutch bypass .I've actually gone through a couple configurations and at this point, I chose to use suggested settings as well as the settings the manual insisted. I've also enabled 3x OEM lock since I want to use my own remote. So far, once I initiate the ready mode sequence, I triple click the lock button and the car cranks for a bit but doesnt start. I've been through the settings a couple of times over to check everything and its not clear to me what might be causing it. Please let me know if there is any additional wiring needing to be done or a certain setting that's causing it not to work. I'm so close to a successful start, yet so far.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue