Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

20/01/2016

 Jeep AJBrown (320Pts.)

1

False Alarms to Compustar CM7000-AS

Vehicle: 2015 Jeep Wrangler  Alarm: (New-Install) Compustar cm7000as w/2W704r-sh long range 2-way RF transmitter  Bypass Module: Fortin EVO-ALL    The only wiring done outside the CAN-BUS are parking lights, siren, hatch trigger and 12v switched connections.    - Doors triggers are connected through CAN-BUS; hood and hatch triggers are hard-wired into Jeep.  - Compustar DAS Tilt/2-stage shock Sensor is currently DISCONNECTED from the brain.  - DEI Proximity Sensor is currently DISCONNECTED from the brain.    About 20% of the time my Compustar will go into full alarm within 5 seconds of arming the system. I thought the issue might have been the proximity sensor so I disconnected it completely. When that didn't work, I also disconnected the DAS tilt/shock sensor with no change (currently no external sensors are connected).    After going into full alarm, pressing disarm turns off the siren but the parking lights continue to cycle through the full timeout period of 30 secs and the doors do not unlock. If I hit disarm a second time, the trigger cycle stops and the doors unlock but there are NO zone breaches indicated on the 2-way remote, by parking light or LED flashes as if the alarm never went off.    When the alarm triggers, I can disarm the system twice, stopping the cycle, and immediately ARM the system with no repeated full trigger.    Next, I disabled all triggers and unused options within the EVO-ALL with no change.  I finally disconnected the data wire from the EVO-ALL and I had not had a false alarm for one day.  I then reconnected the DAS Tilt/2-stage shock sensor and the DEI 508D Proximity sensor and haven't had any false alarms in two days.  This leaves me thinking the problem is either the EVO-ALL or there is something in the CAN-BUS that the EVO-ALL is picking up and causing the false alarms.  I'm hoping someone out there has a suggestion for me.     Thanks in advance for any help you can provide!
Login to reply View 2 answer(s)

19/12/2015

 Jeep AJBrown (320Pts.)

1

EVO-ALL with Compustar CM7000

I want to change my current setup from using a Fortin EVO-ALL as stand alone to Compustar CM7200 Remote starter with the EVO-ALL as the bypass and have some questions.  
    Will I be following Fortin instructions "A - INSTALLATION WITH DATA-LINK" from the PDF guide here (http://fortin.ca/download/28831/evo-all_evochrt5_o20150216.pdf)? Will the Fortin control the door lock/unlock with arm/disarm and monitor door triggers through the CAN-BUS with no additional wiring required? CM7200 Pin 15 Black - Is the Status/Ground wile running, typically used to trigger bypass / transponder modules.  Will this wire be required and, if so, where does it connect on the Fortin EVO-ALL (http://techfeed.compustar.com/ft_controllers/manuals/CM7000_Full_Install_3.00_EN.pdf) Will the factory FOB's lock/unlock and arm/disarm the alarm or will I have to exclusively use the aftermarket remotes?   Will I need to follow the EVO-ALL PROGRAMMING (Page 14 http://fortin.ca/download/28831/evo-all_evochrt5_o20150216.pdf) or is that not required since it's only a bypass for the remote starter on the CM7000?

 

Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue