Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

16/05/2016

 Chevrolet Breon Melson (150Pts.)

2

How to wire a Compustar CM7000 to the Evo-all (Evo-GMT4) using idatalink

I have a 2007 Chevy Avalanche. i purchased CM7000, Evo-All with T-harness, and a drone Dr-3100.

 I installed the evo-all using the T-harness, hoping for a quick and easy installation. After the Evo was installed and programmed, I am able to use the OEM remote to start/stop the vehicle, it works fine.  I then attempted to connect the CM7000 alarm/remote start to the Evo-all using "connection A", installation with Data-Link. Here is where I might be missing something. The instructions detail how to add a remote start to the Evo, so i assume it would be the same for the CM7000 Remote/alarm combo. 

The instructions state that only the the ignition out wire needs to be connected to the Evo-all From the CM7000, and that some alarm require the 12v Battery wire to be connected directly to the T-harness, so I tried it with the 12v wire both ways.

From the CM7000, I connected the 12V Green ignition wire on the Low current ignition harness (CN3) to the yellow ignition wire (A1) on the Evo. i am using a Compustar 2-way remote (2W704R-SH) with the alarm.  it was my understanding that the instalation with Data-link is suppose to greatly reduce the number of wires that you have to connect. I changed option F2 from "Fortin" to "AP-OFA" then the 2-way remote locks and unlocks the doors.

My problem is that when i try to use the 2-way remote to start the vehicle, nothing happens. Its like the alarm is not communicating with the evo or the vehicle. None of the lights on the dash light up.  However I am able to Lock and Unlock the using the 2-way with no problems.   i took it a step further and attempted to connect the Black status out wire from compustuar's 20-pin harness (CN5) to the Ground while running Dk. Blue wire on the Evo, and also the 12v yellow starter output from the compustar ignition harness, to the red/blue start wire of the Evo.  when trying to remote start

    Are there any other wires from the CM7000 that i need to connect (or connect to the Evo) in order for the remote start to work? the Door locks are working fine. I was under the impression that no other connections were needed since i would be using the Idatalink installation. Will any of the the wires (other than the siren, parking light, and hood pin) need to be wired directly to the vehicle in order for this alarm to work or will it all be handled thru the data-link? Does the horn output work thru the data-link or will it need to be wired directly to the vehicle? What could my issue be?

Thanks in Advance!

Login to reply View 1 answer(s)

10/02/2016

 Chevrolet Aaron Mcmullin (190Pts.)

0

04 Astro Van door locks not functioning properly with evo all and compustar

I have a customer with a 2004 Chev Astro van that I had installed a Compustar CM800s and Evo-All in and the keyless when used with the compustar remotes do not operate correctly. The unit will not unlock the passengers door completly,( unlocks half way or acts like it is stuck ) but operates normally with factory remotes and with relays installed. Everything else operates as it should.Firmware version on evo all is 4.06 and have tried various evo-all units.Units were flashed with both hardware versions of flashlink updaters. Compustar is also flashed to current revision.Evo- all was set in fortin and ads bypass mode in options menu. The only method I did not try is hard wire method.I also regrounded the unit twice to eliminate possible ground issues. Any ideas on a possible solution to this? Thanks I have since hardwired the keyless with relays and the problem is resolved.
Login to reply View 1 answer(s)

06/12/2013

 Chevrolet joe catalano (230Pts.)

1

will the compustar remote kits work with the evo - all as as stand alone remote start

looking for more info on R/F KIT 'S FOR EVO ALL
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue