Questions & Answers

Does Evo one support 3x lock to start Ford Transit 250 2016 key start ?
I saw under features it says in some cases it support 3x lock what are those case ?

There is a 3rd party selling a prewired 3x factory remote start based on the Evo-All so it would seem that the Evo-All can be wired as a stand alone (can-bus) remote start but there are no instructions for this application / US version of the Ford Transit.

See link:

https://www.amazon.com/Start-X-Remote-Starter-2015-2019-Transit/dp/B07PM8ZVNJ

Install Video:

https://d2y5sgsy8bbmb8.cloudfront.net/f71daf72-8800-4c9c-8e09-2963fdbb1b99/default.jobtemplate.mp4.480.mp4

In the installation video (2m37s) the Evo green wire (door status?) is connected to the vehicle Purple/Green described as the vehicle lock wire.  Can this connection be explained? 

Also, if this is workable what would be the external trigger wire (ground to start/stop)? 

For the Evo-All and Thar-For1 T harness would the following be correct?:

Yellow/Black from T harness to [A1] Yellow  on 20 Pin connector
Connect [C4] Can Low Grey/Black to Can Low on OBD II
Connect [C3] Can High Grey to Can High on OBD II
Ground Black from T harness

Looking for instructions on any other connection needed ie. lock wire (&diode) and external trigger

There is a 3rd party selling a prewired 3x factory remote start based on the Evo-All so it would seem that the Evo-All can be wired as a stand alone (can-bus) remote start but there are no instructions for this application / US version of the Ford Transit.

See link:

https://www.amazon.com/Start-X-Remote-Starter-2015-2019-Transit/dp/B07PM8ZVNJ

Install Video:

https://d2y5sgsy8bbmb8.cloudfront.net/f71daf72-8800-4c9c-8e09-2963fdbb1b99/default.jobtemplate.mp4.480.mp4

In the installation video (2m37s) the Evo green wire (door status?) is connected to the vehicle Purple/Green described as the vehicle lock wire.  Can this connection be explained? 

Also, if this is workable what would be the external trigger wire (ground to start/stop)? 

For the Evo-All and Thar-For1 T harness would the following be correct?:

Yellow/Black from T harness to [A1] Yellow  on 20 Pin connector
Connect [C4] Can Low Grey/Black to Can Low on OBD II
Connect [C3] Can High Grey to Can High on OBD II
Ground Black from T harness

Looking for instructions on any other connection needed ie. lock wire (&diode) and external trigger

In  flash link manager I choosed the 2015 Ford Ranger (euro), but there was no installation instructions. Which instruction can be used? For 2016 ford ranger(euro)-standalone

Hi,I installed EVO-ALL for Ford explorer 2016 Push-to-start.no OEM alarm.

firmware 71.35 I flashed my FLASH LINK UPDATER2

stand alone.3Lock start.OEM REMORT ON D1

options-Evo Alarm enable

Install was no problem.Same corlor wire and postion than instllation manuals.

But it doesn't work.

Alarm work good.blue led flash when lock or unlock.

alarm work when shock detected.

but no remort starting.

red led flash when lock button 3X.but no respond my vehicle.

same status when negative signal for start/stop external Yellow/Black wire.

it looks try remort start but no work.

At Programming,The install manuals tell "Press the START/STOP button once...The RED LED will flash rapidly 10X times.

But my programming,RED LED flash about 5X times.

I don't know it relataed this problem.

Hi,I installed EVO-ALL for Ford explorer 2016 Push-to-start.no OEM alarm.

firmware 71.35 I flashed my FLASH LINK UPDATER2

stand alone.3Lock start.OEM REMORT ON D1

options-Evo Alarm enable

Install was no problem.Same corlor wire and postion than instllation manuals.

But it doesn't work.

Alarm work good.blue led flash when lock or unlock.

alarm work when shock detected.

but no remort starting.

red led flash when lock button 3X.but no respond my vehicle.

same status when negative signal for start/stop external Yellow/Black wire.

it looks try remort start but no work.

At Programming,The install manuals tell "Press the START/STOP button once...The RED LED will flash rapidly 10X times.

But my programming,RED LED flash about 5X times.

I don't know it relataed this problem.