Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

15/09/2022

 Chevrolet nathan pearce (160Pts.)

0

Need to re and have no more flashes left Service # 001A06609740

Need re flash please
Login to reply View 1 answer(s)

14/03/2022

 Chevrolet crispyrp69 (420Pts.)

0

Decriptor limit

I need to reset flash limit on decriptor. Said reached limit for car. I havent reached any limit. How do I get it reset? My s/n 001A07338367
Login to reply View 1 answer(s)

20/01/2022

 Chevrolet Jeff Nelson (130Pts.)

0

Flashlink updater 4 with viper

I have a Flashlink 4 Updater running current firmwear. I am trying to program an evo all module. When I am going through the steps in the Flashlink Manager and get to protocall Viper isnt an option. Can I not use an evo all with a viper 4806v?
Login to reply View 1 answer(s)

23/12/2021

 Chevrolet garrett fannin (130Pts.)

0

INT-SL+ won't program to 2000 Silverado or be discovered by Flashlink Manager

I have a Fortin INT-SL+. HW Ver 2 Firmware Ver 3.01 mfg date 04/2018 Service number 002102061867 I also purchased a Fortin flashlink-lite updater I have a 2000 Chevy Silverado with an older Chrime Stoppers remote start, and had on omega IB-GMBP.DB-PAS-23A Passkey override. The omega unit went bad and appears to be discontinued. I purchaesd the Fortin unit to replace it. I just need the passkey function of the Fortin. Wired it in configuration 5 without data link. When I follow the programming instructions, the red light will come on, but not start blinking when the key is switched on. I have checked my wiring. I'm pretty sure I have it right. The red light also does not go out after I start the engine. I read on this forum that GM trucks can be particularly hard to program and that there is a firmware version 3.06 that resolves the issue. I bought the Fortin flashlink-lite updater to upgrade my firmware from 3.01 to 3.06 The flashlink-lite updater seems to be working with my laptop correctly. The Flashlink manager 4 shows the flashlink-lite updater as connected. When I plug in my INT-SL+ the red light comes on for a few seconds and goes out. Flashlink Manager4 always shows the "module status" as disconnected. I tried holding the INT-SL programming button before plugging the INT-SL into the Flashlink-lite. The red light stays on but the "module status" doesn't change. I have seen youtube videos that show the Fortin modules connecting almost instantly when plugged into the Flashlink devices, so I think something is wrong. I suspect the INT-SL I don't want to buy more stuff until I'm sure that I'm going to solve the problem. I feel that I should troubleshoot the connection between INT-SL+ and Flashlink first, since those are Fortin factory connections. That eleminates my wiring as a potential issue in the flowchart. Is there a way to tell if the INT-SL+ is bad?
Login to reply View 1 answer(s)

29/02/2020

 Chevrolet Reggie Banks (130Pts.)

0

Flashlink manager is stuck on 70% currently loading questions...did i install something wrong

2015 silverado
Login to reply View 1 answer(s)

19/11/2017

 Chevrolet RONNIE REED (130Pts.)

0

Will the EVO-GMT4 work on a 2010 Silverado without AP8 code?

Will the EVO-GMT4 work on a 2010 Silverado without AP8 code?
Login to reply View 1 answer(s)

20/12/2015

 Chevrolet Clint Kiser (310Pts.)

1

If the Flash-Link Updater does not recognize my module, is the module defective?

I just bought a brand new EVO-ALL and Flash-Link Updater 2. I followed the instructions exactly on the Flash-Link Updater manual in order to get the latest updates for my device prior to install. The Flash-Link powers on and lights up red but the module never lights up and the Flash-Link light does not come on showing a link to the module. Any option I attempt to choose results in a message that the device was not found. Is this brand new module defective? Is there any other way to test it or reset it? Thanks!
Login to reply View 2 answer(s)

22/11/2013

 Chevrolet Kevin Wiggins (140Pts.)

1

Chevrolet Camaro Evo All with THAR

Will I need the flashlink updater to update and program the evo-all to remote start my 2012 Chevrolet Camaro 2LS?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue