Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

24/10/2022

 Infiniti hnagashio@gmail.com (130Pts.)

0

EVO-NIST1 - Yellow LED never solid

I bought my EVO-NIST1 from Amazon for my 2009 Infiniti FX35 (push to start and AT). 1) I followed the installation guide and connected the harness: 　- The keyport 　- OBDII 　- Brake switch 2) The white/black wire (A.19) of the harness is connected to the light blue wire of the push start　button    (Parking light wire (A.14) not connected at this time) 3) Insert key to the keyport 4) With the main unit, press and hold the programinng button and connect the 4-PIN datalink harness  (Other harness connectors not connected)   [Result]  I tried for about 3 minutes and blue, yellow, and red LEDs all blink together, not alternately. Disconnect the 4-PIN connector (main harness) and return to Step 4) above and repeat, but yellow LED never solid.   Do I need firmware update my main unit? I see below on my main unit:  Model: EVO-ALL  Date: 12/2021  SN: 001A07 338558  
Login to reply View 1 answer(s)

03/03/2019

 Infiniti Josh Ley (500Pts.)

0

2009 Infiniti FX35 starts, shuts off after a minute or less

Crimestopper RS7-G4 with evo-all, firmware 72.37. has worked fine for several years. Had an issue several months ago that was resolved by updating firmware to 72.36 and reprogramming tach (would start and stall) Now, it’ll start, stay running, and shut down after a minute. Attempt to restart, run for a shorter amount of time, and same on third attempt. I changed firmware to 72.33, 72.34, 72.35, 72.36, 72.37 all with similar results. 72.32 (as recommended in guide 34361) Is this a faulty module? Or is there another possible solution
Login to reply View 1 answer(s)

26/03/2016

 Infiniti Jason Seidel (280Pts.)

1

Flash Link options A1-A11

I'm setting up my evo-all with NIS1 T-harness as a stand alone remote starter in my 2009 infiniti fx35. In the guide it says to turn on C1 nad D1, and that inturn enables D1.6 and thats all fine. But am I supposed to have everything else turned off? What about A1-A11, these were all turned on before so I left them on. What about D2? Would the guide specifically say I need to set this? One more thing, I might add a smartstart module later, should I turn on this now in the firmware or should I wait?
Login to reply View 1 answer(s)

18/02/2016

 Infiniti S M (200Pts.)

0

2010 FX35 needs to be restarted after remote start

Hello! I've bought a car with remote (I'm assuming forting evo is installed by prev. owner) After remote start launch (by pressing 3 times on oem fob) car is starting, but when you getting in the car in put gear in Drive mode, steering wheel is blocked and does not allow you to unlock untill you have to shutoff the engine and start normally. Also when you opening a trunk cart shuts off as well (on remote start). Please help!! ANy ideas?
Login to reply View 3 answer(s)

18/02/2016

 Infiniti S M (200Pts.)

0

2010 FX35 needs to be restarted after remote start

Hello! I've bought a car with remote (I'm assuming forting evo is installed by prev. owner) After remote start launch (by pressing 3 times on oem fob) car is starting, but when you getting in the car in put gear in Drive mode, steering wheel is blocked and does not allow you to unlock untill you have to shutoff the engine and start normally. Also when you opening a trunk cart shuts off as well (on remote start). Please help!! ANy ideas?
Login to reply View 3 answer(s)

18/02/2016

 Infiniti S M (200Pts.)

0

2010 FX35 needs to be restarted after remote start

Hello! I've bought a car with remote (I'm assuming forting evo is installed by prev. owner) After remote start launch (by pressing 3 times on oem fob) car is starting, but when you getting in the car in put gear in Drive mode, steering wheel is blocked and does not allow you to unlock untill you have to shutoff the engine and start normally. Also when you opening a trunk cart shuts off as well (on remote start). Please help!! ANy ideas?
Login to reply View 3 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue