English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Utilisateur

tjamz0061

À rejoins en date due:

Jul. 21, 2011

Points

340

Commentaire(s)

1

Questions votée(s)

0

Réponses votée(s)

0

Votes positifs

0

Votes contre

0

Votes reçus

2

Votes négatifs reçus

0

Activité récente

Questions demandée(s)

4

Question(s) répondue(s)

1

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question
ACTIVITÉ RÉCENTE QUESTION(S) DEMANDÉE(S)" QUESTION(S) RÉPONDU(S)" QUESTION(S) COMMENTÉE(S)"

20/09/2020

 Toyota tjamz0061 (340Pts.)

0

09 Rav4 PTS EvoOne will not program

So I completed the installation as specified here: https://cdn02.fortin.ca/en/download/24101/24101.pdf When I go through the programming procedure everything works until I get to step 4. The blue light goes out as indicated, but it never flashes or comes on solid so it never completes it's programming. Any suggestions appreciated! I've tried reversing the CAN wires.
Connectez-vous pour répondre Voir 1 réponse(s)

11/02/2018

 Subaru tjamz0061 (340Pts.)

0

2018 Subaru Outback Keystart EVO-ALL Solace S3 (IC4) Won't Stay Running

Just installed a Solace S3 remote starter (IC4 module w/ relay pack v. FW51) using an EVO-ALL in my 2018 Outback with a standard key start. Everything went well. Flashed with 79.45 firmware, did the programming, DCryptor went well also. Car will lock/unlock/hatch release no problem. Tach is programmed via data. Vehicle will start, run for just a couple seconds and shut off. It will attempt this 3 times. The remote says that the car is running (I get confirmation as such) but it still dies.... then attemps restart. I've double checked all wires at ignition. All appears good. Any ideas?
Connectez-vous pour répondre Voir 1 réponse(s)

29/12/2014

 Nissan tjamz (300Pts.)

1

2012 Nissan Armada Smartkey won't stay running

Recently installed a remote start for a customer in a 2012 Nissan Armada. Unfortunately the vehicle is 200 miles away and won't be able to be in the shop until this Sunday (when tech support is closed). I don't have the service number on the EVO-ALL but am 100000% positive that I am using the right firmware and that all connections are proper. When the vehicle left the shop it was working 100% perfectly, however after a day of use the customer noticed that the vehicle would start for only 3 seconds before shutting off. It was long enough that the remote starter saw the tach signal and assumed the vehicle was still running as it was still counting down the timer on the fob, so I'm ruling out starter issue (for now). Does anyone have any other ideas/thoughts on what could be causing this? Would a GWR wire cause this? Is it possible it lost it's transponder programming?
Connectez-vous pour répondre Voir 1 réponse(s)

28/12/2014

 Pontiac tjamz0061 (340Pts.)

1

08 Pontiac Torrent Won't program

So I'm attempting to install an EVO-ALL along with an Ultrastart 3295 remote start. Firmware Version 70.16 When I go to program the blue light goes out and never starts flashing when I get to step #4. At first I noticed the car wouldn't start this way either. Ultimately I determined it was because there wasn't power passing through the White Green wire on connector D to the White Red wire on connector D so I unhooked the entire remote start & bypass module and jumpered the two wires together to verify the car would start that way (it did). Next I reconnected the starter and bypass and removed the jumper that I had temporarily installed and tried programming again... same issue. Anyone have any suggestions?
Connectez-vous pour répondre Voir 1 réponse(s)

15/12/2014

 Ford tjamz0061 (340Pts.)

1

EDIT: New Problem 11 Taurus Regular Key Phantom hood & brake fault

NEW PROBLEM: Vehicle will run for a couple of seconds (15 maybe) and then shut down.... grrrr.... Any advice is welcome While attempting installation on a 2011 Taurus (standard key) I encountered a situation where I was getting phantom hood & brake faults one the remote starter (One-Start OS380). Ultimately I was able to remedy the solution by deactivating those functions of the EVO-FORT1 and hardwiring to the vehicle. I guess this isn't a question really other than to ask if others have had similar issues and what they did to remedy the situation.
Connectez-vous pour répondre Voir 1 réponse(s)

No results

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question

Support Technique

Recherchez parmi nos produits les plus populaires et les sujets d'installation disponibles dans notre section Questions et réponses.

En savoir plus
Téléchargez notre application de guides de dépannage étape par étape disponible pour iOS et Android ou parcourez notre version de bureau.

En savoir plus
Accédez à la plus grande base de données de schémas de câblage et de photos en ligne de l'industrie. Un jeton gratuit est fourni dans chaque boîte EVO-SERIES.

En savoir plus
Vous n'avez pas trouvé l'information que vous cherchiez ? Posez-nous une question en remplissant le formulaire de demande de support technique. Un spécialiste produit vous répondra sous peu.

En savoir plus
Des solutions de contrôle à distance et de connectivité à la fine pointe de la technologie au soutien technique haut de gamme, découvrez pourquoi vous devriez choisir les produits Fortin.

En savoir plus

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer