Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Utilisateur

Ben Kibsey

À rejoins en date due:

Nov. 29, 2013

Points

300

Commentaire(s)

9

Questions votée(s)

0

Réponses votée(s)

1

Votes positifs

0

Votes contre

1

Votes reçus

2

Votes négatifs reçus

0

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question

1

2012 Ford Focus clutch switch bypass

2102 Ford Focus, not push-to-start. Diagrams show two clutch switch locations. One at the clutch pedal which is a basic switch to ground. The wire goes low as soon as the pedal is depressed. I can override that one by grounding the wire. However Ford decided this wasn't good enough and added another switch in the circuit. This wire (Which I found in pin 12, 42 pin connector at the BCM) is actuated only when the pedal reaches the floor, one would hope it is a basic to ground switch as well but it certainly is not. My ohmeter reads 7Megohms resistance to ground at rest and 9ohms when the pedal is depressed. I cannot override this particular wire function by connecting this wire to ground. Has anyone else come across this? The bypass module is evo-all and functions perfect, as well as the prostart remote starter so those two have absolutely nothing to do with this issue. The only thing I need to fix before this setup will work is to make the car start without physically depressing the pedal which in every other case should be to ground the clutch switch.

1

2012 Kia Sedona EVO-ALL will not activate factory security

EVO-ALL with v. 4.18. On a 2102 Kia Sedona. The module seems to program normally.. . I am in W2W mode. It is tied in to the CAN system and the unlock/lock wires from the remote start module. I am not tied in to the vehicles lock/unlock wires. The lights flash during programming to indicate the door locks and the brake/tach have gone correctly as well as the key bypass as the remote start seems to operate properly, except it leaves the headlights on after the programmed runtime expires....I don't know yet if the remote start or the bypass module is to blame for that one Anyways my main problem: If I use the factory fob the doors will lock, activate the security, and flash the indicators. However when I lock the doors with the remote start fob (It is a code-alarm unit) it does lock the doors but fails to activate the factory security....5 minutes later the doors unlock by themselves. I do not see any reason for this or a setting in the remote start manual that pertains to this (function)

No results

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question

Support Technique

Recherchez parmi nos produits les plus populaires et les sujets d'installation disponibles dans notre section Questions et réponses.

En savoir plus
Téléchargez notre application de guides de dépannage étape par étape disponible pour iOS et Android ou parcourez notre version de bureau.

En savoir plus
Accédez à la plus grande base de données de schémas de câblage et de photos en ligne de l'industrie. Un jeton gratuit est fourni dans chaque boîte EVO-SERIES.

En savoir plus
Vous n'avez pas trouvé l'information que vous cherchiez ? Posez-nous une question en remplissant le formulaire de demande de support technique. Un spécialiste produit vous répondra sous peu.

En savoir plus
Des solutions de contrôle à distance et de connectivité à la fine pointe de la technologie au soutien technique haut de gamme, découvrez pourquoi vous devriez choisir les produits Fortin.

En savoir plus

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer