English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

17/09/2018

 Volkswagen Brandon Cleary (1250Pts.)

1

2011 Golf EVO-ONE w/Drone DR-5400 Lock/Unlock issue

Hello! Finally got my EVO-ONE and Drone working on my 2011 Golf manual TDI. I can get the Drone to start and stop the vehicle. I even got it to open the hatch. However it wont lock or unlock the doors. If I hit unlock it seems to engage the ingition for a split second(gauge cluster and radio lights up) then turns off, and then the yellow light comes on. If I hit unlock again it does the same thing and then the yellow light will turn off.(The blue light does not flash at all.) If I hit lock the blue light will flash extremly quickly once but nothing else happens. I don't want to have to keep flashing the unit and hit the flash limit because I can't change options when loaded on 0.50 RS firmware.
Connectez-vous pour répondre Voir 0 réponse(s)

22/12/2017

 Volkswagen yannick polasek2 (1950Pts.)

0

jetta 2012 no lock unlock on can wire?

hi installed evo-one in jetta 2012 puch start. everything programmed good but lock unlock does not work. blue led flash Slightly (not strong blue flash but faint )on evo one but does not lock unlock. version 75.38 installed should i back down to different software?
Connectez-vous pour répondre Voir 1 réponse(s)

03/05/2017

 Volkswagen JPK (260Pts.)

0

2013 VW GTI - Lock/Unlock via CAN does not work on EVO-ALL

I have an EVO-ALL installed in a 2013 VW GTI Automatic as a standard installation with a Compustar CM7200 remote start module. I wired up the module as shown in the installation guide, but the lock/unlock functions do not operate correctly. Nothing happens with a lock command. With an unlock command, the ignition pulses on, but the doors do not unlock. Any help would be appreciated.
Connectez-vous pour répondre Voir 1 réponse(s)

18/01/2017

 Volkswagen Yuanjun Kang (210Pts.)

0

EVOALL+VIPER 4806V installed for 2017 VW tiguan push to start, no lock unlock,no start

hi, i installed a Fortin EVOALL+VIPER 4806V remote starter for my 2017 volkswage tiguan with push to start.

i use DATA-LINK wire to connect the bypass module and remote starter. so there is only a few wires need to be connected.

i flashed evoall with firmware 75.25 and the evoall programmed successfully on the car.

i didn't connect the parking light wire for the remote starter. i'm confused for the parking lights wire connection.

the fortin manual shows there should be a RS3 OUT PARKING LIGHTS(-) wire connect to a relay PIN 86.

But the VIPER quick reference install guide shows there is only: a H/4 WHITE/BROWN LIGHT FLASH ISOLATION WIRE -PIN 87a light flash relay and a H/5 WHITE PIN 30 of LIGHT FLASH RELAY

so should i use a relay to make the connection? but how? or there is a realy inside the remote starter? anyway i didn't connect the wires for the parking lights.

should i connect a hoop pin switch to make it work?

For the VIPER 4806V remote starter:

set light flash polarity to -, set horn input polarity jumper to -,

connected the H1 ,H2 wires(6 PIN connector),

Neutral safety switch plugged in and in the ON position.

door lock plug NOT plug in,

ground pin 13 black /white (-) neutral safety /parking brake input (as the manual mentioned) ---- 24PIN connector,

control center connected,

connected the pin8 * IGNITION1 INPUT/OUTPUT (8 PIN connector on viper)

 

For the EVOALL :

every wire connected as the manual said.

so here is the problem:

when i press the lock button , the door lock no action. i can hear one click sound coming from the viper brain.seems it wants to trigger the parking light to flash one time.

press the unlock button,door lock no action. two click sound coming from the viper brain.

press the remote start button the car wouldn't start. ignition doesn't go on. and i hear 5 click sound from the viper brain. which means :Brake wire is active .

i used a Digital Multimeter to test every wire from the car connector pin to the VIPER and EVOALL pin. all good!

reset the EVOALL module. nothing changed! took the EVOALL off the car to reflash it. i can enter every menu EXCEPT the EVO-ALL OPTIONS. Always shows unit is not connected.and stuck there.

my computer system is windows10. i tryed diffrent computers,diffrent USB port. nothing changed.  

 

 
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer