Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

TPMS Light after EVO-ONE install; lots of Communication Lost codes

Hi, so after my remote install, the TPMS light is on all the time. I understand during remote start this is normal, but this is all the time. I have checked all my tires, they are within normal range. So I ran a code pull on all CANBUS systems, and the result was CURRENT/HISTORY lost communications codes on several modules, one being the TPMS system. It is system code B1247, Main Body ECU Lost Communication... however there are several others too, a dozen or so, to other systems. I thought perhaps they were historical from when I disconnected everything to connect the T harness, but I cleared them and all came back, after I tried clearing just the TPMS code unsuccessfully. I attempted clearing the current/history lost communication code. The light went out for about half a second, and it came back quickly. Checked codes again, it was back. Not sure if that screen shot is visible, all I can see is a placeholder symbol. I will place a share link in my google drive to the code list. VIN removed, but it is a 2018 Toyota Corolla H-Key using THAR-T18 (think the kit i bought was EVO-ONE-T18?, I'll reference and update, but it was the EVO-ONE kit containing the T18 harness) I am presuming this is possibly a programming issue with the EVO-ONE module since the OBD2 port passes thru, but not sure. This is my first experience with Fortin products and do not want to start messing randomly with settings I do not fully understand yet. I've done remote starts before but this is my first Fortin system, switched because of the quality level; I do have a EVO-FLASH unit and have the ability to flash/reprogram everything myself, I have all tools and interfaces needed to make it work, thanks in advance. Details are below: 2018 Toyota Corolla H-key, EVO-ONE, THAR-3 / THAR-18, RF442 installed, TPMS-hijack installed to allow OEM remote start (working OK since installed) https://drive.google.com/file/d/1wVWxhNDwFs4chpdfGXHE7lqC3UKpKHwd/view?usp=sharing

0

2021 Tundra TPMS Not Working

Everything is currently working as it should. However, after tapping into the TMPS wire, now my TPMS flashes and the truck no longer reads the tire pressure. Is there a workaround for this, or is this normal?

0

2021 Toyota Corolla TPMS

After starting the car remotely with the OEM key. The TPMS signal begins to link. Once it starts up, the TPMS signal goes off, but it leaves a warning on the car that the TPMS sensor is not working properly and I need to go to the dealer. Used module, Fortin Evo One 2021. How could I solve this problem? Thank you very much in advance. Installation method, wire to wire.

0

Toyota camry TPMS cable

I have a 2020 toyota camry, installed an evo-one and t harness, I interrupted TPMS cable as per installation but, the car starts fine, unlock the doors with oem remote but I have tpms light on, when tried to configure it by manual dealer instruction it shows "tpms malfunction visit your dealer" any ideas? Thanks

0

Toyota camry TPMS cable

I have a 2020 toyota camry, installed an evo-one and t harness, I interrupted TPMS cable as per installation but, the car starts fine, unlock the doors with oem remote but I have tpms light on, when tried to configure it by manual dealer instruction it shows "tpms malfunction visit your dealer" any ideas? Thanks

28/12/2020

Toyota G M (15170Pts.)

0

tpms on toyota

I set evo-one to 2018 camry and 2019 rav4. On both I made a tpms connection. On both, the tire symbol flashes when remote start with 3-lock. How to find out whether or not this vehicle has a TPMS?

0

EVO-ALL - OEM Fob not working to unlock after remote started. TPMS is cut and works.

I flashed EVO-ONE to latest firmware, used the wizard to set my settings, then went into pro mode and followed the steps in documentation to select XL202 RF kit, and installed in the vehicle. The SmartStart module is not yet installed. 3x lock works with OEM fob but once started, the OEM fobs no longer work to lock/unlock the doors. I did cut the TPMS wire and does not flash when started with key or after key is in ignition and turned to ON. I did test alternating the D6 and D4 wires on the cut TPMS wire but still had no unlock from fob after remote start. My suspicion is that since the TPMS light doesn't flash in standard operation, enabling the RF kit might have something to do with this but since I didn't test the install before I enabled that, I'm not sure. Is there something else I might be missing?

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer