Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

why is the car not starting with remote starter

hello I have installed an evo one 942 with a T harness toy14 on a 2023 toyota rav4 hybrid. It was working a couple time and during my final checks the remote starter will not start vehicle. It accepts the signal, locks and unlock vehicle but won't start or turn ignition on. when I push the start button on remote the park lights come on for a few seconds and then nothing. the red led does flash when locked and remote started. Help Please

30/11/2023

Toyota DMPNJ (210Pts.)

0

2007 Toyota RAV4- No immobilizer

I’m installing an Evo One in a 2007 Toyota Rav4. The car does not have an immobilizer. What are the steps to program the module? I’m not finding it anywhere. Thanks

05/10/2023

Toyota Moike (580Pts.)

0

2022 rav4 lane departure lights up installed evo one 441 push start

2022 rav4 installed evo one with rf441. vehicle starts and stops but when you start driving the lta(lane departure is getting triggered

0

Low battery causing horn to go off on 2017 RAV4 hybrid?

Our 2017 RAV4 hybrid was parked for a few weeks causing the battery to run down as it has a tracker installed. All of a sudden one morning the horn faintly started to go off intermittently. There was no one around it. Is it possible that it was the Evo that’s installed in it was causing it to go off? Thinking that someone was messing with the battery? If so is it possible to disable this as it keeps going until the battery is basically completely dead. We have since charged the battery and are driving it every few days and there has been no issue since. Thanks

17/09/2023

Toyota akm (850Pts.)

0

2019 Rav4 push start not following the step to start

Yesterday i followed the steps and car was able to start with factory remote 3 lock on my 2019 RAV4 PUSH START using Toy13 Harness. Today i was planning to add Evo start and it is not following even key start option nor Evo start 2. Light is yellow/amber on evo one module. Please let me know what i am missing. Evo one serial number is 002B04 248000. Thanks for help.

0

Hood pin wire 2017 Toyota RAV4 Hybrid

Where would I need to tap the pink/black wire from the Evo one for the hood pin switch on the interior? I believe it's on the body control module but I'm not sure which connector or wire. I would rather use the factory hood switch if possible rather than installing the aftermarket one and not have to run a wire through the firewall. Thanks

0

RFK442 not programming with Evo One for a 2009 RAV4 using HAR-ONE- TOY1 harness

I have programmed and installed an Evo-One using THAR-ONE- TOY1 harness in my 2009 Toyota RAV4, automatic transmission, standard key (dot key). Module S/N: 002B04211739, https://photos.app.goo.gl/gBSQdCrRweH1cRnC7   Bypass Firmware: 79.49, https://photos.app.goo.gl/PbEQgYMP1RPx6PgA8 Remote starter firmware: 1.25, https://photos.app.goo.gl/DkLyv2ttWCip77wS7   I have double checked the wiring connections, and seems everything is good.   Image 1: https://photos.app.goo.gl/uPvX8uTQnyqcuEyU9, Image 2: https://photos.app.goo.gl/TH6jQ8A2BPpa6H7P9 I can start the car remotely using the OEM keys. I would like to use the RFK442. I have tried to programming/pairing the RFK442, unfortunately I could not able to proceed after steps 3, page 2 in the following RFK442 programming manual.    https://fortin.ca/download/68451/rfk442-install-guide-68451.pdf The problem is: at step 3, the antena LED blinks once and then goes away (but the instruction says "The LED will turn ON").  At step 4, when I press the brake paddle 4 times, the antena LED doesn't response or no rapid flashing (instruction says "The LED will flash rapidly"). It seems like the RFK442 can not communicate with the Evo One.  I appreciate if you have any suggestion to overcome this issue and complete programming the RFK442 with the Evo One.  

0

RFK442 not programming with Evo One for a 2009 RAV4 using HAR-ONE- TOY1 harness

I have programmed and installed an Evo-One using THAR-ONE- TOY1 harness in my 2009 Toyota RAV4, automatic transmission, standard key (dot key). Module S/N: 002B04211739, https://photos.app.goo.gl/gBSQdCrRweH1cRnC7   Bypass Firmware: 79.49, https://photos.app.goo.gl/PbEQgYMP1RPx6PgA8 Remote starter firmware: 1.25, https://photos.app.goo.gl/DkLyv2ttWCip77wS7   I have double checked the wiring connections, and seems everything is good.   Image 1: https://photos.app.goo.gl/uPvX8uTQnyqcuEyU9, Image 2: https://photos.app.goo.gl/TH6jQ8A2BPpa6H7P9 I can start the car remotely using the OEM keys. I would like to use the RFK442. I have tried to programming/pairing the RFK442, unfortunately I could not able to proceed after steps 3, page 2 in the following RFK442 programming manual.    https://fortin.ca/download/68451/rfk442-install-guide-68451.pdf The problem is: at step 3, the antena LED blinks once and then goes away (but the instruction says "The LED will turn ON").  At step 4, when I press the brake paddle 4 times, the antena LED doesn't response or no rapid flashing (instruction says "The LED will flash rapidly"). It seems like the RFK442 can not communicate with the Evo One.  I appreciate if you have any suggestion to overcome this issue and complete programming the RFK442 with the Evo One.  

0

Which harness should I use with EVO-ONE in 2022 Toyota RAV4 LE?

I'm going to get EVO-ONE for my 2022 Toyota RAV4 LE, H-key. In the spring I checked recommended solution: EVO-ONE and THAR-ONE-TOY12. But now the website suggests THAR-ONE-TOY14... Which one should I get? and what's the difference? I want to use it just with Toyota key for remote start, no separate module. Thanks in advance!

0

No remote start on 2017 Toyota rav4 push to start

I recently installed the evo all on my 2017 rav4 push to start using the evo all and thar toy6 t harness. The module took programming but i have no remote start. The module is attempting to start but no dash lights or remote start. Followed the instructions for t harness install and programming and no luck. Also used connector A which was labeled from factory.

0

Check engine light on after remote start, low fuel warning light, AWD malfuction

On DEC.8, 2021 I posted my question "H-KEY 2020 TOYOTA RAV4 LE EVO ONE WITH T-HARNESS REMOTE STARTER INSTALLED - SYSTEM MALFUNCTION" and got answer. I did what recommand to do, evnen hardwiring CAN HIGH/LOW  two wires and use RAV4 CAN connector plugged in ECU, no luck.

My rav4 remote start problem more like this after a few weeks oberservation

    Use OEM remote or RFK442 remote, the low fuel yellow light show up after remote started, When going in the car, key in the key cylinder and turne to ON position, press brake, key taking over. The yellow low fuel light disappear, and fuel display needle moving up to level. After a few times remote starting, when you try another remote starting, the check engine light show up, and screen also shwing "AWD System Malfuntion. 2WD Mode Engaged, Visit you r dealer"

The CHECK ENGINE light was P2067: generic fuel level sensor "B" circuit low. I am wondering that low fuel level sensor B dosen't powered up  when remote started, then ECU set the CHECK  ENGINE light. I reset it by OBDII, but it keep coming. If no remote starting, RAV4 going normal by the OEM key and no warning light.

Is this could be a communication issue between EVO ONE and RAV4 ? The IGNITION signal from EVO ONE should go power up fuel level sensor B when remote starting, but it doesn't. 

Any idea? Could you please look at 2020 RAV4 LE AWD(Canadian version) wiring diagram, see how.

Thanks in advance! 

 

0

Issues with Fortin EVO ALL on 2021 Rav4 push to start non-Hybrid

EVO-ALL firmware 79.69 push to start non-hybrid. Flashed with the recommended settings using the wizard and verified current settings: A1:A10 = on, A11 = off, A12 = on, A13:B3 = off, C1:D1 = on, D2:D5 = off, D6 = on, D7:G = off, H2 = on (for the RFK912 install). First attempt at installation, bypass was programmed successfully and 3x lock started the vehicle. Once I programmed the two RFK912 remotes, the vehicle would not turn on with the remotes. Reset the unit using master reset procedure (red light and hold until all colors flash) and reflashed the unit and ram the decryptor. Nothing worked on the second try but the unit recognizes when I press the RFK912. Vehicle starts and runs normally using the push button start. Ran through master reset, reflash, and decryptor a few times with the same results. Now I am getting a decryptor limit reached error for SN 001A07 272320. Please help - this is my second install on a RAV4 of the same year and the first install went flawlessly.

0

Issues with Fortin EVO ALL on 2021 Rav4 push to start non-Hybrid

EVO-ALL firmware 79.69 push to start non-hybrid. Flashed with the recommended settings using the wizard and verified current settings: A1:A10 = on, A11 = off, A12 = on, A13:B3 = off, C1:D1 = on, D2:D5 = off, D6 = on, D7:G = off, H2 = on (for the RFK912 install). First attempt at installation, bypass was programmed successfully and 3x lock started the vehicle. Once I programmed the two RFK912 remotes, the vehicle would not turn on with the remotes. Reset the unit using master reset procedure (red light and hold until all colors flash) and reflashed the unit and ram the decryptor. Nothing worked on the second try but the unit recognizes when I press the RFK912. Vehicle starts and runs normally using the push button start. Ran through master reset, reflash, and decryptor a few times with the same results. Now I am getting a decryptor limit reached error for SN 001A07 272320. Please help - this is my second install on a RAV4 of the same year and the first install went flawlessly.

0

connecteur bouton start Toyota RAV4 hybride 2017

Bonjour, pouvez-vous me dire comment accéder au connecteur du bouton poussoir start du RAV4 hybride ? merci

0

H-KEY 2020 TOYOTA RAV4 LE EVO ONE WITH T-HARNESS REMOTE STARTER INSTALLED - SYSTEM MALFUNCTION

    Just bought Fortin remote starter kit EVO-ONE with RFK442 THAR-ONE-TOY12 for this 2020 RAV4 LE, H-KEY. Installed yestoday, the OEM 3xlock working, fist try it remote started the car; programmed RFK 442 one remote, got remote started on first shot also, OEM key fob stay function. Good job. Moved car to drive way from garage, double check the lock and unlock fuctions again from both OEM and RFK442 remotes. Remote started car, when driving to street showing "system malfunction". I read those simillar questions, can't get answer. EVO ONE bypass firmware 88.20, remote start firmware 1.25. Please help. What should I check?

0

T-Harness Rav-4 2021 XLE push

Bonjour, J'aimerais savoir si le T-Harness THAR-TY70 est le même que le THAR-TY13 pour un toyota Rav-4 2021 bouton poussoir. Sur le site il me suggère Evo-One + THAR-TY13 et sur le plan on parle de THAR-TY70. Je voulais également que vous me confirmiez que la prise en charge était bien fonctionnel puisque Idatastart ne le fait pas. Je vous remercie beaucoup et bonne fin de semaine à tous.

0

Remote start takeover for 2021 Toyota RAV4 non-hybrid with smart key?

I want to verify the remote start options for the 2021 Toyota RAV4 (non-hybrid, with smart key, and without factory remote start) DOES HAVE the takeover capability?  In other words, does your remote start systems keep the vehicle running when the door is opened after being remote started?  Toyota's with the factory remote start have a ridiculous feature where the vehicle shuts off when a door is opened after being remote started.  I am looking for a remote start system that does not shut the vehicle off when a door is opened after being remote started?

0

Guide 93711 2019 Toyota Rav4 Hybrid--is option D4 required (hybrid mode)?

Install guide doesn't mention enabling option D4 for Hybrid mode, although the guide is specific for Hybrid. Is this an oversight, or is it not required for this vehicle?

0

2010 RAV4 dot Key fail to program

I have EVO-ONE-Toy and a T harness. I get thru the key recognition (10 red flash) but no blue lights. I have checked my CAN high and CAN low multiple times. Any Suggestions ? Also have tried with 79.48 and 79.64. Trying to keep this simple with 3x lock to start.

0

2008 Rav4 - Will EVO One do key take over?

HI I'm looking to install an EVO One to act as a car starter on a 2008 Rav 4, automatic transmission, no push to start, no keyless entry. It looks like the EVO One will work as a stand alone starter, what I'm not clear on is if it will also do key take over? That is can we remote start the car with an EVO One, unlock the doors (and not have the engine shut down), slip the key in the barrel and turn it and drive off? Or will the engine shut off as soon as we unlock and open the door?

0

RAV4 2005 Connector exist but no transponder at ignition key

I am doing a RAV4 2005, Regular Key, Regular EVO One instlation,wire t wire. I founf the connector for the transponder hanging under the steering colum but there is no transponder at the ignition switch. I looked everywhere no transponder only a key sense. The car is stock and no modifiction done on it. I pluged the tx/rx pink/red-blue on the connector but the connector dosent go any where just connected to the harness. Is it possiple this car has no transponder but the diagram is wrong. when I programed the module I get the solid red instead of the rapidly flashing one. I tried 3 evo ones product same problem. Could somebody explain how to make remote start on this car?

0

Toyota Rav4 2020 Push start doesn't crank.

Installed following instructions. Remote is manufactured 2019.11. Tried various firmwares - from the one recommended in the instructions (79.57), and the newest version (79.64). When plugged in, blue light shines dimmely. When pushing the car-start, the ignition lights come on but doesn't crank -it tries 2 times and turns off.

0

2016 Rav4 push to start rempte start was working for 3 months and now does not with key fob or phone app

0

No sound when alarm is activated (2013 Rav4 EVO-ALL with t-harness)

I installed the EVO-ALL on a 2013 Rav 4 with push to start using the TOY6 t-harness. I made no connections other than the plug-in connectors (guide 70391). The t-harness includes a wire on A4 - this is the wire I used for a horn on my one other install (guide 12971). Remote start works & the parking lights flash when the alarm is triggered, but there is no audible alarm. If I adjust G1 to horn instead of siren, the door locks are activated alternately as the horn would be when the alarm is triggered. Guide 8821 shows A4 is 'door status' for this car so maybe this makes sense. What do I need to change to allow for an audible alarm? Thanks!

0

2020Toyota Rav4 evo all with tharness remote starter stopped working - system malfunction showing

So i installed evo all with tharness on a 2020 toyota rav4 push to start(not hybrid). It was working okay for a while then customer told me today that it stopped working and the vehicle dash shows a message that says "System Malfunction. Please see manual" any idea what is goin on? Also notice that when i remote start before when it was still working that parking light flasher 3x twice before starting. Well it starts and stops okay so i didnt bother with it. any help will be much appreciated. Thanks a lot

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer