Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

How do you program the crimestopper Revo 1 with an Evo One. The install is being completed on a 08 Nissan Pathfinder LE

Cant seem to get the module to read the new crimestopper remotes

0

Evo-all and compustar rf remotes

Hi i bought a evo-all and a compustar 4900s and after trying to install the compustar system to the evo-all and had no luck, I decided to to see if I could just use the remote and antenna with the evo-all rather then the compustar remote start. And if its possible to just add the antenna and remotes to the evo. How would one go about doing that?

0

rf kit program setting, door unlocking

what setting do i need to enable to install RF442 on 2014 nissan versa with standard key.im using t harness thar one nis5. how do i program the rf kit and do i need to connect pin a1 to pin a8 if i dont want to use rf kit to unlock or lock just need remote start.

0

Evo-all and compustar rf remotes

Hi i bought a evo-all and a compustar 4900s and after trying to install the compustar system to the evo-all and had no luck, I decided to to see if I could just use the remote and antenna with the evo-all rather then the compustar remote start. And if its possible to just add the antenna and remotes to the evo. How would one go about doing that?

1

What is required to install an EVO ALL on a 2020 Sentra with push to start?

I know I need a ring antenna for the OEM remote. Do I need an RF kit to use the remote start function, or will the OEM remote work? I notice there is a remote start module in the wiring diagram in the install guide. Is this a separate module I need to purchase?

0

2016 VERSA NOTE STD KEY - NO TRANSPONDER, UNABLE TO PROGRAM EVO-ONE

This 2016 Nissan Versa Note doesn't seem to have a transponder. Transpoder connector isn't located at the key cylinder as shown in install diagram. Wired everything up as shown for install diagram, but didn't connect the RX or TX connections as the transponder wires aren't there. I can't get it to program. Getting stuck on the 5th step of programming. The 5th step starts with the yellow LED solid and you turn key to ON/RUN and the red LED should light alongside the yellow. I'm not getting that red LED lit.

I went into the settings and turned off the transponder for the Evo-One but still having the same issues. Super basic install. Any help would be much appreciated.

0

rm 942 rf kit with 4 button remote will only start and shut down the car what am i missing to control locks etc?

i have a 2010 nissan murano and last xmas i installed the evo all with the t-harness successfully. I just installed the rf kit RM942 with one 4 button remote. the factory remote still works as it should and starts the vehicle as well. the 942 remote will only start and stop the engine but will not lock/unlock the doors or open/close the trunk. I did update the firmware and set the H2 option for the rf kit. what did i miss? thank you for your help jason

0

2016 VERSA NOTE STD KEY - NO TRANSPONDER, UNABLE TO PROGRAM EVO-ONE

This 2016 Nissan Versa Note doesn't seem to have a transponder. Transpoder connector isn't located at the key cylinder as shown in install diagram. Wired everything up as shown for install diagram, but didn't connect the RX or TX connections as the transponder wires aren't there. I can't get it to program. Getting stuck on the 5th step of programming. The 5th step starts with the yellow LED solid and you turn key to ON/RUN and the red LED should light alongside the yellow. I'm not getting that red LED lit.

I went into the settings and turned off the transponder for the Evo-One but still having the same issues. Super basic install. Any help would be much appreciated.

0

2004 350z remote start doesn't work with evo-one

To start off with... the instructions were wrong, somebody at fortin assumed that a 2005 350z BCM is identical across all model years of 350z and that wasn't the case, I had a HUGE hassle trying to find the correct wires for my 2004 350z BCM but i believe with 99% accuracy i wired things correctly, now with this out of the way, after installing everything, programming the module, using the dcryptor, and even successfully programming the RF remote, it doesn't remote start. it locks and unlocks fine with the RF remote, but when i click remote start, it sends the signal and the module receives it, and it blinks red telling me it couldn't remote start, in fact absolutely nothing happens. not even the ignition or accessories being turned on. i do have 2.3 enabled in the options which is the correct harness configuration. I don't understand why it doesn't remote start. it's like no power at all is being sent does anybody have any idea why? Also why does this guide below for the rf kit have used pins on the 20 pin connector, specifically "bypass ignition", "ignition" and "start"-- https://cdn02.fortin.ca/download/33021/rf642w-install-guide-33021.pdf --that this guide below NOT have? http://cdn02.fortin.ca/download/78221/evo-one_ig_thr_bi_nis-350z-xterra_key_a_78221.pdf do those ignition and start wires from the 20 pin connector go somewhere? i tried grounding them, i tried leaving them unconnected, I tried wiring them to the ignition and starter wires on the 6-pin connector, and it never made a difference. someone please help.

0

2004 350z remote start doesn't work with evo-one

To start off with... the instructions were wrong, somebody at fortin assumed that a 2005 350z BCM is identical across all model years of 350z and that wasn't the case, I had a HUGE hassle trying to find the correct wires for my 2004 350z BCM but i believe with 99% accuracy i wired things correctly, now with this out of the way, after installing everything, programming the module, using the dcryptor, and even successfully programming the RF remote, it doesn't remote start. it locks and unlocks fine with the RF remote, but when i click remote start, it sends the signal and the module receives it, and it blinks red telling me it couldn't remote start, in fact absolutely nothing happens. not even the ignition or accessories being turned on. i do have 2.3 enabled in the options which is the correct harness configuration. I don't understand why it doesn't remote start. it's like no power at all is being sent does anybody have any idea why? Also why does this guide below for the rf kit have used pins on the 20 pin connector, specifically "bypass ignition", "ignition" and "start"-- https://cdn02.fortin.ca/download/33021/rf642w-install-guide-33021.pdf --that this guide below NOT have? http://cdn02.fortin.ca/download/78221/evo-one_ig_thr_bi_nis-350z-xterra_key_a_78221.pdf do those ignition and start wires from the 20 pin connector go somewhere? i tried grounding them, i tried leaving them unconnected, I tried wiring them to the ignition and starter wires on the 6-pin connector, and it never made a difference. someone please help.

0

EVO-ONE programs fine according to lights, no response from OEM or RF keyfobs?

2012 nissan frontier. Orderd EVO-ONE remote start and bypass with rf kit from crutchfield. spoke with personall there and went over the way everything is connected to insure it is connected correctly. I updated the software/firmware of the EVO-ONE using flashlink 4. Set everything to recomended settings. now i get no response from the keyfob. the only time the blue light on the antenna lights up is when it is first plugged in. Only flashes for a second then gone. no response when pushing any button on the new keyfobs and can only lock and unlock with factory keyfob, their is no remote start action with x3 lock button. what did i do wrong?

0

how to connect ftx 64-2w

i do not have a four pin connector to connect this connector to. how does it connect to the box?

0

RF remote unlock button unlocks and then relocks doors

Installed an EVO ONE on a 2006 Nissan Armada with a Fortin rf642w RF remote. Everything is working fine except the unlock from the RF remote. Lock functions as it should (Although I can hear it lock a second time after it is already locked), but the unlock isnt working. Pressing the unlock causes it to unlock and then immidiately relock. Factory remote continues to function as it should. Any advice would be appreciated.

0

How to get Evo one to program RF remote for 2011 Nissan frontier

0

How to get Evo one to program RF remote for 2011 Nissan frontier

0

can you program funtions without the use of an rf remote

im using the oem remote to start vehicle with the lock button of the oem remote. to change the funtions the directions say i need to use a remote that is already programmed, is this the only way to change the functions?

0

can you program funtions without the use of an rf remote

im using the oem remote to start vehicle with the lock button of the oem remote. to change the funtions the directions say i need to use a remote that is already programmed, is this the only way to change the functions?

0

Juke will not 3x or RF start start without the OEM key in the car.. plus a few other problems

EVO ALL THAR-NIS1 with RF kit FTX64-2W installed in a 2015 Nissan Juke PTS. Easy install but had a heack of a time with the flashlink. Repeatedly told me that the device was disconnected when I would select save. Updated to the latest verion and went with the bare minimum selections only selecting what was shown in the manual.. D1 C1 H2. I know that theres more to be selected but seemed that when I would select what made sense.. it didn't like it and would disconnect when saved. So as of right now it is loaded with those basic commands. The module programming itself went smooth and ended with the slow blue pulse.. went through steps twice. I failed to include the service number last week.. same question but sn is now included. So with basic commands loaded I placed it back into the car and introduced the RF transmitters and moved on to the final steps... testing. I found that the car will not remote start with the oem fob or the RF fob unless the oem fob is in the car. Also, the rf fobs will not remote lock/unlock but does flash the lights.. can't remember if oem fob was in car or not? I did connect the lock/unlock wiring which was somewhat confusing by the diaagram.. it specifies in the instructions that 12 is blue and red is 13 but if you look at the pictures you have listed, its not that at all... If you count out the pins you'll see what I mean. I went by the picture.. Lastly, it was time to call it a day and button the car up and reschedule and I noticed that the parking lights were on. I can't recall but I believe it was while the car was locked but not 100% certain. The only way to get the lights to go away was by unplugging the module.. We're going to have another shot at this later today and any help is greatly appreciated.

0

Juke will not 3x or RF start start without the OEM key in the car.. plus a few other problems

EVO ALL THAR-NIS1 with RF kit FTX64-2W installed in a 2015 Nissan Juke PTS. Easy install but had a heack of a time with the flashlink. Repeatedly told me that the device was disconnected when I would select save. Updated to the latest verion and went with the bare minimum selections only selecting what was shown in the manual.. D1 C1 H2. I know that theres more to be selected but seemed that when I would select what made sense.. it didn't like it and would disconnect when saved. So as of right now it is loaded with those basic commands. The module programming itself went smooth and ended with the slow blue pulse.. went through steps twice. I failed to include the service number last week.. same question but sn is now included. So with basic commands loaded I placed it back into the car and introduced the RF transmitters and moved on to the final steps... testing. I found that the car will not remote start with the oem fob or the RF fob unless the oem fob is in the car. Also, the rf fobs will not remote lock/unlock but does flash the lights.. can't remember if oem fob was in car or not? I did connect the lock/unlock wiring which was somewhat confusing by the diaagram.. it specifies in the instructions that 12 is blue and red is 13 but if you look at the pictures you have listed, its not that at all... If you count out the pins you'll see what I mean. I went by the picture.. Lastly, it was time to call it a day and button the car up and reschedule and I noticed that the parking lights were on. I can't recall but I believe it was while the car was locked but not 100% certain. The only way to get the lights to go away was by unplugging the module.. We're going to have another shot at this later today and any help is greatly appreciated.

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer