English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

05/12/2022

 Nissan Ahmed Aboushouk (330Pts.)

0

Fuse rating for EVO-ALL power supply

I am about to install EVO-ALL for Standalone installation ( without the T-Harness ) for a nissan Qashqai ( Rogue sport in CA ) with push to start ( Guide # 83931 )

S/N of my EVO-All is : 001A07026604

I have three main questions so i can complete the installation :

1- Fuse rating for the power supply of the module ( between B4 pin and 12v battery )

2- Diodes direction is confusing me as the Ignition A4 pin is an output pin which means that Current should flow from EVOALL to the car BCM pins while the Diodes direction says the opposite  ( cathode at top meaning current flows from BCM pins to EVOALL )

3- Which is more recommended for a way of control to disable remote starting when needed ( i cannot have Alarm functions beside remote starting for this vehcile ) where 2nd option would completey shut off the power to EVOALL :

- Adding ON/OFF switch on the Hood Pin A8( connecting other switch end to ground )

- Adding ON/OFF switch on B4 pin on the same line of the Fuse ( connecting other switch end to ground )

  Many thanks in advance for your support & cooperation
Connectez-vous pour répondre Voir 1 réponse(s)

30/04/2018

 Nissan Jehad Alyousef (190Pts.)

0

where does the A8 (dark Blue) wire connects on 2015 Nissan Armada Intelligent Key?

I just want to make sure that the meant by "The Driver Door Pin" where the A8 Dk. Blue wire connects is that switch located at the body frame and controls the inside capin lights? is this is the correct interpretation? Thanks
Connectez-vous pour répondre Voir 1 réponse(s)

29/01/2018

 Nissan Ariel Alcaide (130Pts.)

0

What is the easiest way to connect a door pin wire on a 2014 Nissan Maxima?

I've installed a evo combo ( EVO-NIST1) and the only connection I haven't done is the door pin because I don't know where the BCM plug is located on the vehicle. Some say behind the cluster and other say behind the glovebox. It's funtion is for the auto lights.
Connectez-vous pour répondre Voir 1 réponse(s)

10/07/2017

 Nissan Arnold Cabanit (130Pts.)

0

EVO ONE Defective PIN A8

I installed evo one on my 2011 Nissan Rogue and been using it for 3 weeks from now. I added some DEI voice alarm module but it didn't work because the PIN A8 (Ground-when-armed Dark Blue wire) has a constant ground even the system has been disarmed.

I used an LED Bulb to test PIN A8 by connecting the negative wire of the LED BULB on the PIN A8 wire and the positive wire on the battery and the LED BULB lights up both on Disarmed and Armed.

And because the PIN A8 is defective, I temporarily removed it on the driver side door pin wire because when I close the driver door, the module reads it as open (remote start will not work) and when I open the driver door, the system reads it as closed (remote start will work).

Is there any way to fix the issue on my evo one.

Mahalo.

 

Connectez-vous pour répondre Voir 1 réponse(s)

10/07/2017

 Nissan Arnold Cabanit (130Pts.)

0

EVO ONE Defective PIN A8

I installed evo one on my 2011 Nissan Rogue and been using it for 3 weeks from now. I added some DEI voice alarm module but it didn't work because the PIN A8 (Ground-when-armed Dark Blue wire) has a constant ground even the system has been disarmed.

I used an LED Bulb to test PIN A8 by connecting the negative wire of the LED BULB on the PIN A8 wire and the positive wire on the battery and the LED BULB lights up both on Disarmed and Armed.

And because the PIN A8 is defective, I temporarily removed it on the driver side door pin wire because when I close the driver door, the module reads it as open (remote start will not work) and when I open the driver door, the system reads it as closed (remote start will work).

Is there any way to fix the issue on my evo one.

Mahalo.

 

Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer