Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

2008 Dodge Avenger ignition on but won't start

Installed EVO-ALL and T-harness on 2008 dodge avenger. Configured it for standalone per guide #64051, connected green/red wire to purple and yellow to yellow in the T-harness. All other wires just taped back, no hood pin installed. EVO seemed to program correctly. Pressing 3X lock on remote turns on ignition, but car doesnt start. Also will not start with the key. Sets code P0513 - incorrect immobilizer key. I can remove the T-harness and reconnect the ignition plug back stock and the car starts like normal with the key. I tried several different configurations and updated then downgraded the firmware on the EVO, but nothing I did made any difference. It seems like the EVO is not managing the immobilizer function. SN: 001A07 096654. Any ideas?

1

Why does my car shut off when using the key after Evo All install?

Edit: if i replace the factory harness it has the same jssue. Hello. Thank you in advance for your time & help! I have a 2013 Dodge Avenger SXT. I purchased an Evo All unit from Amazon that came "pre configured" for "plug and play use." I was able to install it by plugging the t harness into the immobilizer unit that is next to the ignition. It programed fine. It works great! Starts car remotely using the factory fob (lock X3). However, Now when I go to start the car using my key the car starts and then stops after 1 second. The red "security system" light on the dash blinks. I have to shut off the car and then start it with the RS unit to get it to run. I believe that I must have broken the solder connection on the SKREEM unit "antenna" when I installed the Evo, is this correct? And, if so, is the fix simply removing the SKREEM unit and resoldering the "antenna?" Thanks again!

1

Why does my car shut off when using the key after Evo All install?

Edit: if i replace the factory harness it has the same jssue. Hello. Thank you in advance for your time & help! I have a 2013 Dodge Avenger SXT. I purchased an Evo All unit from Amazon that came "pre configured" for "plug and play use." I was able to install it by plugging the t harness into the immobilizer unit that is next to the ignition. It programed fine. It works great! Starts car remotely using the factory fob (lock X3). However, Now when I go to start the car using my key the car starts and then stops after 1 second. The red "security system" light on the dash blinks. I have to shut off the car and then start it with the RS unit to get it to run. I believe that I must have broken the solder connection on the SKREEM unit "antenna" when I installed the Evo, is this correct? And, if so, is the fix simply removing the SKREEM unit and resoldering the "antenna?" Thanks again!

0

Dodge Avenger 2011 - Stand Alone Install

Installed the EVO-ALL with THAR-CHR5 harness on a 2011 Dodge Avenger. I updated the firmware to the latest 74.23. Turned on C1 and D1 options. Programmed the unit succesfully but it does not remote start with 3x lock. I see the led flash blue when I press lock on the OEM key. I have not hooked up the Parking Light Out as of yet, but this it an output and shouldnt prevent the car from starting? Also in the instructions I don't really see where the External Input is connected to. I have tried just grounding this input with the same results. Any help would be appreciated. I have the programmer to change options. I followed instructions C for the installation. Thanks.

20/12/2014

Dodge G M2 (130Pts.)

0

2013 Dodge Avenger Parking Light

I was wondering if a resistor is needed for the parking light connection on an Avenger. I have read conflicting information. Also when doing the polarity swapping relay, it is connected to apply full 12 volt correct? Its not looking for a resisted ground or some different signal correct? Thank You

0

2012 Dodge Avenger 12 volt constant wire location for parking lights

12 volt constant  wire location on a 2012 Dodge Avenger  for parking light turn on  for a evo all

0

stand alone remote starter parking lights

2012 dodge avenger stand alone remote starter no parking lights!

1

2011 avenger parking lights dont work

using evo all as stand alone and trying to get parking lights to work but brown/white wire doesnt produce ground to activate relay. lights work if i ground relay to a different ground. any suggestions to get it to work

1

Check engine light comes on with EVO-ALL when initiated..

My evo-all works fine until now on 2010 didge avenger! my check engine light comes on when it engage/initiated of remote start unit. What gives? I had to disconnect my car battery to reset to get it start the engine plus I've head and search for similar problem could it be the DTC causing the check engine light to come on otherwise everything work fine when my engine is started light, horn and etc but when it failed to remote start my display panel on the console "NO BUS" when my fob is inserted. Any idea or solution?

-1

Need HELP with a 2011 dodge avenger stand alone remote start.

I have followed the instructions and cannot get it to work. Please help!

1

08 advenger used evo all bypass when starting car opens trunk why???

instaled ultra start remote starter with evo all bypass folowed wire color wireing diagram and evo all conection 1 and prgram 1 I also found that the wires to the transponder are not the same colors but test the same as diagram powers in the same spot and grond in same spot all wires seem to be ok .car does start and unlock and lock everthing works good exceot win starting trunk opens just wondered why???? thx tom butler also checked all powers and grounds to unit .they are ok 12 volts and under load 11.5 volts . ground is not pulling down under lod seems to be good tryed ground in two diff spots

0

Starting range is limited 13 Avenger EVO-CHRT5

While everything works perfect at close range, it is hit and miss from a distance, even though the doors will L/UL

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer