English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

24/08/2020

 Toyota W. Frazier (210Pts.)

0

2016 Toyota Corolla Evo One

I have used the Toy 8 Harness that came with the Evo One,Module (TOY 8 79/xx/1.xx C1, D5 38.2 Progam Lock). I followed all the steps and when I plug the 20 Pin Connector in the Evo Module, the noise sounds and the dash board warning message says, TURN LIGHS OFF and when I try to Press the button 10 times, the RED and BLUE LEDs fade out by the time I get to 6. I can't get Pass Step 3! I reset it a few times and still the same thing! I switch the Pins and try to use it as a TOY 3 Harness and the same Thing! I even Hard Wired the module using the Diagram and still the same thing! I'm thinking this was a bad Module from the beginnig! I have listen to TECH Support ideas and tried them and nothing works! I've made 7 attempts on wire this Evo One, trying different ways and the Module keeps doing the same thing every time. I'm ready to give up! Any idea, why this Warning Light coming on? Do this warning light be the reason why I can't ger pass Step 3?
Connectez-vous pour répondre Voir 1 réponse(s)

19/08/2020

 Toyota W. Frazier (210Pts.)

0

2016 Toyota Corolla with H key,

After following the diagram and I go through the steps! When I go to plug the 20 Pin connector in the EVO ONE, it makes a noise like the lights are left on and the Dash Board warning say's TURN LIGHTS OFF! When I unplug the 20 Pin connector, the noise goes awayand the dash bord warning for TURN LIGHTS OFF, goes away! I try to program the EVO ONE Module with the noise and TURN LIGHTS OFF, by pressing 10 times, the light stop around the 5th to 6th press and it won't let me get pass Step 3. I reset the Module and did and Master rest and still have the same problem!
Connectez-vous pour répondre Voir 2 réponse(s)

19/08/2020

 Toyota W. Frazier (210Pts.)

0

2016 Toyota Corolla with H key,

After following the diagram and I go through the steps! When I go to plug the 20 Pin connector in the EVO ONE, it makes a noise like the lights are left on and the Dash Board warning say's TURN LIGHTS OFF! When I unplug the 20 Pin connector, the noise goes awayand the dash bord warning for TURN LIGHTS OFF, goes away! I try to program the EVO ONE Module with the noise and TURN LIGHTS OFF, by pressing 10 times, the light stop around the 5th to 6th press and it won't let me get pass Step 3. I reset the Module and did and Master rest and still have the same problem!
Connectez-vous pour répondre Voir 2 réponse(s)

06/01/2017

 Infiniti Brenan Salgado (230Pts.)

0

Remote start doesn't turn on dash lights or air conditioning/heat

Hello all. I have a 2005 Infiniti G35 (automatic; not intellikey, not push start) and I just installed a Fortin EVO-ONE with the NIS2 T-Harness and a Compustar Slice Remote. I can lock, unlock, release the trunk, and remote start/stop the car. My problem is that when I remote start, the A/C does not turn on (and neither do the dash lights). I have to physically insert my key and turn it to on in order for the A/C to turn on. Regarding connected wires:

    A8 (Dk. Blue) (- GRW) is not connected to anything A15 (Pink/Black) (- Hood pin) is not connected to anything D6 (White/Red) (Security light) is not connected to anything D4 (White/Green) (Security light) is not connected to anything Lt. Blue on the T-Harness isn't connected to anything Lt. Blue/Black on the T-Harness isn't connected to anything I cut the security light wire in the g35 (identified via wirecolor diagrams). The wires aren't connected to anything.

Is there anything I'm missing or do I have to turn on a specific setting via Flashlink Updater 2 (which I have)?

Thanks in advance for your help.

Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer