English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

25/03/2023

 Jeep mike hogg (160Pts.)

0

2016 jk manual bypass

I have the evo all with the CHRT5 wiring harness hooked to the jeep, and everything is programmed, and we'll start with me in the vehicle in the clutch pressed in. How do I bypass the clutch so it will start with the remote not in the vehicle? thanks
Connectez-vous pour répondre Voir 1 réponse(s)

26/02/2020

 Jeep Natalie Maldonado (880Pts.)

0

P0830 code came up after weeks of nstallation (EVO ONE with manual transmission bypass 2017 Wrangler)

After installation of 5 pin relay and successful remote start, the check engine light came up randomly....so far two times. What can be wrong?
Connectez-vous pour répondre Voir 1 réponse(s)

23/08/2019

 Jeep yannick polasek2 (1950Pts.)

0

Clutch problem ( check engine light) wrangler 2018

Check engine light comes on every to often because of clutch bypass using mr20 relay. Need scan tool to remove then ok for a few weeks then comes back in again. Wrangler 2018 standard key evo one + t-harness
Connectez-vous pour répondre Voir 2 réponse(s)

23/08/2019

 Jeep yannick polasek2 (1950Pts.)

0

Clutch problem ( check engine light) wrangler 2018

Check engine light comes on every to often because of clutch bypass using mr20 relay. Need scan tool to remove then ok for a few weeks then comes back in again. Wrangler 2018 standard key evo one + t-harness
Connectez-vous pour répondre Voir 2 réponse(s)

19/02/2019

 Jeep Les Antle (230Pts.)

0

clutch bypass for 2018 wrangler

how do i bypass ckutch on 2018 jeep wrangler with push-to-start?
Connectez-vous pour répondre Voir 1 réponse(s)

13/01/2019

 Jeep Kevin Sergeeff (130Pts.)

0

14 jeep wrangler jk manual

What do I need to install on a 14 jk manual? can I use a t-harness? which one? how do I program it to reserve mode ?
Connectez-vous pour répondre Voir 1 réponse(s)

05/12/2018

 Jeep Anthony Minaudo (190Pts.)

0

Yellow LED flashes 5x after vehicle shutdown

using the fortin evo all as a bypass for a passive keyless entry on my 2014 jeep wrangler manual transmission. The device is set to be a bypass module and not a stand alone remote starter. Ive been able to bypass the clutch and program the device, but once i power down my vehicle the fortin module will flash yellow 5x and then it wont work till i reprogram it again. Initially it thought it was because if the clutch bypass, but that works so any help is appreciated.
Connectez-vous pour répondre Voir 1 réponse(s)

31/10/2018

 Jeep Anthony Minaudo (190Pts.)

0

2014 Jeep JK Clutch bypass

installing a push to start system with my 2014 jeep wrangler JK. I have managed to prove everything programmed well and was usable while the clutch was pushed in. The moment i released the clutch, my EVO-All displayed a RED LED and i had to reprogram for it to work. I suspect this is due to a clutch switch bypass that is required Here are my questions - I see a 5 pin relay that needs to be used but i also see a note that i can use the EVO-ALL relay? - I'm also reading this relay will not allow cruise control. Is this true? If so, is there a way to bypass momentarily but keep the fortin programmed when bypass is not engaged? I would like to install a switch to disable the clutch bypass when the vehicle is being serviced or for use with cruise control. Please help
Connectez-vous pour répondre Voir 1 réponse(s)

28/11/2013

 Jeep Jesse Hir (680Pts.)

1

12' Jeep Compass Doesn't Start unless Clutch pressed

I have a evo-all and chrt5. Hooked up with a Ultra Start 3296m. The vehicle is a 5spd standard trans. Hooked up d2d as per instructions.Install guide 20130219 connection A. No park lights are hooked up. When I try to remote start the vehicle the ignition turns on the dash lights up and heater blows but DOES NOT crank over. Being a standard trans you must set remote starter before exist and the vehicle stays running until doors are closed. Then vehicle shuts down. When remote starter is activated the doors unlook and lock before trying to start. Dash turns on but no crank. What could be going on?? Evo-all is flashed to 4.09 then to 4.18 then to 74.08 none seem to make any difference. UPDATE**** If I hold the clutch down the vehicle will start. How do I wire this to be bypassed????
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer