Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

Signals, headlamps, etc not working after remote start.

2019 Elantra GT manual with EVO ALL, Compustar CMX. Vehicle starts properly, but after a remote start sequence the signal, headlamps and a few other accessories related to steering wheel mounted controls do not work. Only way to regain operation of these functions in to remove cars battery for a few minutes. Happens only after 5-8 remote start sequences. Removed parking light control from EVO and hard wired directly to Compustar with appropriate resistor with no change.

0

Evo One won't start after 5 min or so but was working right after key bypass programming procedure

Hi, I'm kind of lost here, nobody seem to have the answer to my problem, not even Fortin when I call them for help. I installed my Evo One on my Hyundai Tucson 2020 standart key start, followed exactly all the wiring as per the guide, double check all my connection (EMS, CAN BUS, ignition wires, etc) and there's no loose cable. After that I did the key bypass programming procedure with EMS cable : hold down program button while plugging the 6 pin heavy gauge wire till it was red, plug all the others wires, press 7 times program button till it flash 6 times every second, put the key in and turn to ON. At this point the red led flashed 10 time quickly and after stayed on while the blue light started flashing quickly too. After that I turned Ignition to OFF and every light turn off. Right after that I tried to start the car by pressing LOCK, UNLOCK, LOCK and the car started no problem. I then stop the car, close the door and wait... 5 min later, I tried to restart the car with the remote starter but it didn't work. The car got the lock unlock lock signal but no light is flashing on the module anymore like if it went into sleep mode or something. I tried many thing and here is what I found out : - If I unplug all cable from the Evo One and plug it straight back it then start receiving signal again for the next 5 min or so. - If I open the trunk and close it back, the module seem to start back receiving signal from oem remote. To me it feel like there is a cut off or something that stop the module from receiving any signal from the oem remote after a certain amount of time, kind if it was to prevent from draining the battery of the car. Could also be that the Evo One is loosing the key programming after current shutting off in the car but then it shouldn't start by just unplugging and replugging the 6 pin ignition wires. *Sorry if my english is not perfect, I usually speak french.

0

Evo One won't start after 5 min or so but was working right after key bypass programming procedure

Hi, I'm kind of lost here, nobody seem to have the answer to my problem, not even Fortin when I call them for help. I installed my Evo One on my Hyundai Tucson 2020 standart key start, followed exactly all the wiring as per the guide, double check all my connection (EMS, CAN BUS, ignition wires, etc) and there's no loose cable. After that I did the key bypass programming procedure with EMS cable : hold down program button while plugging the 6 pin heavy gauge wire till it was red, plug all the others wires, press 7 times program button till it flash 6 times every second, put the key in and turn to ON. At this point the red led flashed 10 time quickly and after stayed on while the blue light started flashing quickly too. After that I turned Ignition to OFF and every light turn off. Right after that I tried to start the car by pressing LOCK, UNLOCK, LOCK and the car started no problem. I then stop the car, close the door and wait... 5 min later, I tried to restart the car with the remote starter but it didn't work. The car got the lock unlock lock signal but no light is flashing on the module anymore like if it went into sleep mode or something. I tried many thing and here is what I found out : - If I unplug all cable from the Evo One and plug it straight back it then start receiving signal again for the next 5 min or so. - If I open the trunk and close it back, the module seem to start back receiving signal from oem remote. To me it feel like there is a cut off or something that stop the module from receiving any signal from the oem remote after a certain amount of time, kind if it was to prevent from draining the battery of the car. Could also be that the Evo One is loosing the key programming after current shutting off in the car but then it shouldn't start by just unplugging and replugging the 6 pin ignition wires. *Sorry if my english is not perfect, I usually speak french.

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer