English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

18/11/2018

 Cadillac Joshua Ramey (130Pts.)

0

Evo-one will not 3x lock start with oem remote

2006 Cadillac Ext. has factory alarm but no remote start. On advice from a friend that is a certified installer, I bought an EVO-ONE since he said it would work with the factory remote and be able to do the 3x Lock with the OEM remote. The unit was installed properly and double checked via installer. Initially, it would not move past having a solid blue led because of yellow wire (A1) on 20 pin connector not being connected, was connected and checked again (this is not shown as needed in the wiring diagram). Initial settings were not allowing for the data signal to be picked up so the unit was re-flashed to 70.18 and the data signal was able to be found and programmed. All applicable settings are as suggested and 3x lock is enabled in the settings with the flash-link. The unit is now programmed properly for the bypass but will not remote start the truck via OEM remote and 3x lock. Needed to use the vehicle and wasn't able to get anywhere with support on Saturday since they're closed. Current firmware flash confirmed: Bypass: 70.18 firmware, 2.0 hardware Starter: 1.24 firmware, 7.0 hardware Thanks for any help.
Connectez-vous pour répondre Voir 0 réponse(s)

09/09/2014

 Chevrolet tvcity (190Pts.)

0

06 Avalanche factory alarm goes off intermittently

this unit has been in use for about a year & now sometimes when unlocking doors the alarm goes off. when you open the door. Using evoall with compustar CM 6200. Any suggestions on what may be causing this. We reprogrammed the evoall but problem still persists. Not able to get the unit to act up in the shop. Thanks in advance Don
Connectez-vous pour répondre Voir 1 réponse(s)

17/03/2014

 Chevrolet Kacey` GIBBS (140Pts.)

1

wiring a 2002 chevy avalanche with a passlock-2 v.2

I have a 2002 chevy avalanche. I can not tell were the wires go to. I found out on here tp tie the orange and orange black together and tie them to the yellow but it says not to cut the yelow but me remote start says to cut it. could you please tell were the wires go.
Connectez-vous pour répondre Voir 1 réponse(s)

30/12/2013

 Chevrolet Rodney Fulk (140Pts.)

1

Want information on how to access data bus on EVO-ALL

I currently own a 2003 Chevy Avalanche with Factory Keyless Door openers. I am looking at possibly installing the EVO-ALL device into my vehicle to allow me to install a car alarm/ car starter unit. I am also working on a project with this vehicle that requires me to integrate computers into my truck that I build with the intent of controlling all systems in my truck. I will be using a mixture of ARM and PC based computers to build a unique and sophisticated system. With this in mind I was originally going to fully wire an older alarm and bypass module into this truck but with the advent of the EVO-ALL this greatly reduces my need to do so. To make full use of this unit I need to access the data port and be able to communicate with it. I am a college student working on programming and security degrees and plan to use this full truck automation as my Capstone for both degrees so I am hoping I can use a system such as your EVO-ALL with a compatible alarm system and be able to interface to them with either the PC or ARM computers to both monitor and manipulate their functions as required. I have many years of past experience of programming and of interfacing computers to laboratory equipment so I believe this to be a very easy project for me once I have the information. I am hoping to be able to connect with one of your engineers so I can try to obtain the protocol and all necissary information to accomplish this. Thanks for your time! Rodney
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer