Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

29/08/2020

 Toyota ARUN Chandran (240Pts.)

0

2013 Toyota Venza takeover?

I have Evo All hardware version 6 latest firmware, when I open the door the vehicle shuts off, is takeover available?
Login to reply View 1 answer(s)

24/08/2020

 Toyota W. Frazier (210Pts.)

0

2016 Toyota Corolla Evo One

I have used the Toy 8 Harness that came with the Evo One,Module (TOY 8 79/xx/1.xx C1, D5 38.2 Progam Lock). I followed all the steps and when I plug the 20 Pin Connector in the Evo Module, the noise sounds and the dash board warning message says, TURN LIGHS OFF and when I try to Press the button 10 times, the RED and BLUE LEDs fade out by the time I get to 6. I can't get Pass Step 3! I reset it a few times and still the same thing! I switch the Pins and try to use it as a TOY 3 Harness and the same Thing! I even Hard Wired the module using the Diagram and still the same thing! I'm thinking this was a bad Module from the beginnig! I have listen to TECH Support ideas and tried them and nothing works! I've made 7 attempts on wire this Evo One, trying different ways and the Module keeps doing the same thing every time. I'm ready to give up! Any idea, why this Warning Light coming on? Do this warning light be the reason why I can't ger pass Step 3?
Login to reply View 1 answer(s)

19/08/2020

 Toyota W. Frazier (210Pts.)

0

2016 Toyota Corolla with H key,

After following the diagram and I go through the steps! When I go to plug the 20 Pin connector in the EVO ONE, it makes a noise like the lights are left on and the Dash Board warning say's TURN LIGHTS OFF! When I unplug the 20 Pin connector, the noise goes awayand the dash bord warning for TURN LIGHTS OFF, goes away! I try to program the EVO ONE Module with the noise and TURN LIGHTS OFF, by pressing 10 times, the light stop around the 5th to 6th press and it won't let me get pass Step 3. I reset the Module and did and Master rest and still have the same problem!
Login to reply View 2 answer(s)

19/08/2020

 Toyota W. Frazier (210Pts.)

0

2016 Toyota Corolla with H key,

After following the diagram and I go through the steps! When I go to plug the 20 Pin connector in the EVO ONE, it makes a noise like the lights are left on and the Dash Board warning say's TURN LIGHTS OFF! When I unplug the 20 Pin connector, the noise goes awayand the dash bord warning for TURN LIGHTS OFF, goes away! I try to program the EVO ONE Module with the noise and TURN LIGHTS OFF, by pressing 10 times, the light stop around the 5th to 6th press and it won't let me get pass Step 3. I reset the Module and did and Master rest and still have the same problem!
Login to reply View 2 answer(s)

12/04/2020

 Toyota travis white (130Pts.)

0

2013 Toyota Tundra starts for a few seconds then shuts off

I have tried everything. I am pretty sure it's programmed correctly. It starts then shuts down seconds later. I am all out of ideas and ready to give up. Service number 002BO7 339682
Login to reply View 1 answer(s)

14/11/2019

 Toyota aleksei gaidoutskii (130Pts.)

0

2013 Tacoma Evo one lights won't turn off after time out until doors are opened

Everything work except when remote starter times out the lights stay on and wind go off unless the door is opened
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue