Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

13/12/2019

 Nissan Justin Naylor (130Pts.)

0

08 Nissan Pathfinder - RF642W Lock Button Locks, Unlock Button Locks, Programming Settings or Wrong Wire?

2008 Nissan Pathfinder S - Standard Key - OEM Alarm Fortin EVO-ONE With NIS2 Harness Guide Followed: 75611 Unit was flashed to recommended/newest firmware prior to install. Service No: 002B07 200206 Everything is installed and working (As far as the Remote Starter Goes). When using the OEM Remotes the vehicle will lock and unlock as it always has. However, when using the RF642W remotes, The remote start works flawlessly (Push button, parking lights on, start/Crank, Run) The lock button locks the doors, but the unlock button also locks them (and does not unlock). The OEM Remote will unlock the door as normal with the remote starter running, but I would really like to not have to carry two remotes with me. Vehicle Running Oem Remote: Only Solid Yellow is on, No Blue Flashes RF642W: Lock - Solid Yellow, Blue Flash - Locks Doors RF642W: Unlock - Solid Yellow, Blue Flash - Locks Doors Did I miss a step? Enable/disable a wrong option? Any help is greatly appreciated. Thank You in advance.
Login to reply View 1 answer(s)

13/12/2019

 Nissan Justin Naylor (130Pts.)

0

08 Nissan Pathfinder - RF642W Lock Button Locks, Unlock Button Locks, Programming Settings or Wrong Wire?

2008 Nissan Pathfinder S - Standard Key - OEM Alarm Fortin EVO-ONE With NIS2 Harness Guide Followed: 75611 Unit was flashed to recommended/newest firmware prior to install. Service No: 002B07 200206 Everything is installed and working (As far as the Remote Starter Goes). When using the OEM Remotes the vehicle will lock and unlock as it always has. However, when using the RF642W remotes, The remote start works flawlessly (Push button, parking lights on, start/Crank, Run) The lock button locks the doors, but the unlock button also locks them (and does not unlock). The OEM Remote will unlock the door as normal with the remote starter running, but I would really like to not have to carry two remotes with me. Vehicle Running Oem Remote: Only Solid Yellow is on, No Blue Flashes RF642W: Lock - Solid Yellow, Blue Flash - Locks Doors RF642W: Unlock - Solid Yellow, Blue Flash - Locks Doors Did I miss a step? Enable/disable a wrong option? Any help is greatly appreciated. Thank You in advance.
Login to reply View 1 answer(s)

07/01/2018

 Nissan anthony spires (130Pts.)

0

RF remote unlock button unlocks and then relocks doors

Installed an EVO ONE on a 2006 Nissan Armada with a Fortin rf642w RF remote. Everything is working fine except the unlock from the RF remote. Lock functions as it should (Although I can hear it lock a second time after it is already locked), but the unlock isnt working. Pressing the unlock causes it to unlock and then immidiately relock. Factory remote continues to function as it should. Any advice would be appreciated.
Login to reply View 1 answer(s)

21/01/2017

 Nissan Ron DeCanio (270Pts.)

0

Fortin 642 remote only unlocks doors if button clicked twice

I am using EVO-ALL with NIST1 and Fortin 642 RF remote on 2009 Nissan Maxima push to start. Everything works fine, except door unlock only works when unlock button on remote pressed 2 or 3 times. I'm getting confirmation on remote after i push it once that command received, but nothing happens.
Login to reply View 1 answer(s)

24/10/2016

 Nissan Christopher Herman (190Pts.)

0

Accessory Slots on Evo-All/NIST1

Installed a EVO-NIST1 on a 2012 Nissan Altima along with a Fortin RF642W RF kit. Everything works great! However, I'd like to use the RF remote to open the trunk ([-] & lock) as well as turn the rear defrost on ([-] & unlock) using the accesorries slot on the EVO. According to wirecolor.com the trunk release neg is Pin 147 on the grey BCM connector. Similarly, the rear defrost neg is Pin 19 on the green BCM connector. However, the install guide provided for the NIST1 doesn't show which wires are the auxillary outputs. Other EVO I've installed AUX 1 was the orange wire and AUX2 was the orange/black wire. Are these wires still the AUX outputs for the NIST1 or have they been disabled? If they are enabled will I need to place anytype of resistor between the AUX output of the EVO or can I simply tap into the existing wire? Unit: EVO-ALL Hardware: 6 Firmware: 72.24 Wired as stand alone
Login to reply View 2 answer(s)

24/10/2016

 Nissan Christopher Herman (190Pts.)

0

Accessory Slots on Evo-All/NIST1

Installed a EVO-NIST1 on a 2012 Nissan Altima along with a Fortin RF642W RF kit. Everything works great! However, I'd like to use the RF remote to open the trunk ([-] & lock) as well as turn the rear defrost on ([-] & unlock) using the accesorries slot on the EVO. According to wirecolor.com the trunk release neg is Pin 147 on the grey BCM connector. Similarly, the rear defrost neg is Pin 19 on the green BCM connector. However, the install guide provided for the NIST1 doesn't show which wires are the auxillary outputs. Other EVO I've installed AUX 1 was the orange wire and AUX2 was the orange/black wire. Are these wires still the AUX outputs for the NIST1 or have they been disabled? If they are enabled will I need to place anytype of resistor between the AUX output of the EVO or can I simply tap into the existing wire? Unit: EVO-ALL Hardware: 6 Firmware: 72.24 Wired as stand alone
Login to reply View 2 answer(s)

26/08/2015

 Nissan Valeria Grundy (130Pts.)

0

EVO-ONE will not remote start on 2015 Nissan Armada

Using EVO-ONE bypass firmware version 72.19, t harness and RF642W 2-way remotes on 2015 Nissan Armada with Intelligent Key. Remotes will lock/unlock and communicate with vehicle, but will not remote start vehicle. Noted during key programming that module does not operate park lights, so no park light flash code to use. Module programming, key programming, and remote programming completed, but vehicle will not start with remotes. Will make two attempts to start (can tell by driver's foot light operating), but dash lights do not come on and vehicle does not start. Occasionally, vehicle alarm will sound after first attempt (of two) to start. Module programming LED will flash after failure to remote start. Does not appear to be a flash code. While attempting to start, various module LEDs will flash on and off briefly. 2 way communication works properly (remote beeps to indicate remote start failure), and lock/unlock function of remote work normally. Query of vehicle status works normally. All wiring double checked using guide #17763. Ignition diode indicated in EVO-ONE box (rev. 20150225) installed.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue