Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

Module Not picking up the signal of the key

I flashed and updated the module also plugged in the T-Harness But Module light stays solid blue after the x5 flash is there something on this harness that needs to be hard wired it does have a blue wire and a yellow wire hanging from the T-Harness Wiring Diagram is confusing 2015 Mazda 6 Automatic

0

Module Not picking up the signal of the key

I flashed and updated the module also plugged in the T-Harness But Module light stays solid blue after the x5 flash is there something on this harness that needs to be hard wired it does have a blue wire and a yellow wire hanging from the T-Harness Wiring Diagram is confusing 2015 Mazda 6 Automatic

0

Wiring issue Mazda 3- 2015-PTA-Automatic

I boutght The mazda EVO-All with T-harness for my 2015 Mazda PTA automatic and I am confused about the wiring on number 2,3 and 4 in red circles.

On guide #62681 page 6 at the bottom of the page(#2 in red circle) it says that I need to connect LT.BLUE/BLACK Wire to Pin#8 and the Lt.Blue wire to #9 pin on 32-pin White connector.my question is how am I supposed to do this?Do I need to disconnect the 32-pin White connector from Car and connect these 2 wires individually to the part which is attached to the car or the part wich I disconnect from the car?there is no conncetor in the harness to connect these 2 wires.

I have the same issue with #3 and #4 in RED circles at the bottom of the page 6 as-well.how am I supposed to conncet the D section on Evo-All to #1 & #3 on the 8-pin White connector and also connect 4A an 4B on the engine compartment.

I do not see any part on the harness to coonect these parts.am I supposed to buy connectores,strip the wires and attach the wires by myself?there is no extra connector or pin or wire stripper in the package.

Thanks for your help.

 

0

Flashing Red LED After Programming

After first stage of programming the EVO-ALL with my Mazda 3 '15, programming with the computer, then following steps 1-12 again (Guide 62681), the EVO flashes RED with no other lights. I tried following all steps again a few times, with the same result. The security light on the car rapidly flashes for a few seconds as well. What should I try next?

0

2015 Mazda 3 PTS no yellow light during programming

Under hood there is a pin where instructions show a blank pin for jumper. Installing Evo-All with mazt1 t harness

0

Cannot get past solid blue light when attempting the second pass after Dcrytor

I have started from fresh multiple times on a 2015 Mazda CX-5,I get through steps 1-12 ok , hook up to laptop, do the Dcryptor program, go back to vehicle hook up the module , data link first then other connectors, then disconnect data link , then all other connectors. Then start at step 1 again, get to the solid blue light but when trying the step 5 with the OEM remote again the blue light stays on solid no matter how many times I retry the steps, I have an EVO-MAZT1, and have done the evo all Master reset numerous times as well to get back to a fresh starting point, enabling this vehicles recommended options as instructed. I always get everything to work as per instructions but cannot past the second pass solid blue light. I tried downgrading the firmware as suggested by someone else that was having the same problem. This is a push to start vehicle. This is not the first Evo that I have installed but just happens to be the wife's.

0

EVO-MAZT1, Guide 62951, 2015 CX-5 step 16 then to 1-12 steps

I get as far as step 15 , install the Dcryptor, then step 16 says to first install the 4 pin data connector, then the other connectors, step 17 says to go back and repeat steps 1-12. Does this mean remove all the connectors that step 16 asked me to install before starting at step one again, or just disconnect the data connector and press and hold the program button. I am a little confused on how to repeat steps 1-12 again if step 16 asked me to install all the connectors and never asked me to remove them.

0

Mazda CX-5 won't remote start after installation and D-cryptor process.

Evo 1 THAR-ONE-MA30 2015 Mazda CX-5. Installation and programming went just as installation guide instruted that it would. After D-cryptor process, no remote start. Could not acess function programming. Valet button has no response. Blue LED lights with lock button from OEM remote.

0

Mazda CX-5 won't remote start after installation and D-cryptor process.

Evo 1 THAR-ONE-MA30 2015 Mazda CX-5. Installation and programming went just as installation guide instruted that it would. After D-cryptor process, no remote start. Could not acess function programming. Valet button has no response. Blue LED lights with lock button from OEM remote.

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue