Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

07/08/2020

 Other Matthew Currie (130Pts.)

0

Remote start status (eg. Wiper Interrupt) when GWR (Dark Blue A8) is configured for RAP pulse per Function 32 Mode 3?

Product: EVO-ONE Vehicle: 2010 Toyota Tacoma (Standard 40-bit Key) Configured per Fortin application note I am looking for a signal (negative or positive) to indicate that the EVO-ONE has remote started the vehicle and that it is currently running. Ultimately looking to slave features such as wiper inhibit, defrost, etc. I understand that the Dk. Blue A8 "GWR" configured as Function 32 - Mode 1 or Mode 2 would be exactly what I need however I am required to configure GWR as Mode 3 for "Autolight shutdown" per the installation guide for my vehicle. I haven't looked at the signal with a scope or logic analyzer to confirm but it sounds like it will pulse ground only at the end of the remote start run but otherwise float high impedance. I have scoured all documentation I can find but am wondering if there is another pin which may have an undocumented setting or alternative function which could be used for this? I suppose in this case, I could force GWR line back to Mode 1 and then program a microcontroller to then mimic the RAP signal needed for Autolight shutdown -- but -- hoping there is a trick I am missing.
Login to reply View 1 answer(s)

18/01/2020

 Chevrolet Brett Brown (130Pts.)

0

2005 Chevy colorado, RAP. While remote started the driver door trigger is staying engaged.

This causes the door not to be able to be locked. It locks then unlocks because the truck thinks the key is in anf driver door is open. Also the radio stays on after remote shutdown.
Login to reply View 0 answer(s)

17/02/2019

 Infiniti thirty7th (130Pts.)

0

How do I disable seat memory settings

Is there a way to disable seat memory settings prior to entering the car? When I open the door the seats move into the preset position. Ideally it would be better if the seats would move AFTER I've entered the vehicle and closed the door. Reggie Brown
Login to reply View 1 answer(s)

20/12/2018

 Nissan DANG TRUONG (280Pts.)

0

Do I need to Turn On D7 Rap Disable For door pin connection.?? or just leave it off.

Is D7 Rap Disable, Need to trun ON for rap shutdown. on 2014 nissan murano
Login to reply View 1 answer(s)

25/10/2018

 Ford rob reeves (260Pts.)

0

2016 Fusion RAP stopping when engine is shut off remotely or times out not working

2016 Ford Fusion, Standard Key, EVO ONE with T Harness. All connections made including those listed as optional. Relay used for Parking Lights, Driver Door Pin on pin 33 of BCM green violet to A17 ... A18 as per instructions. No T Taps - everything soldered. Remote start functionality fine.  With the RAP connection the voltage from the auto's bcm side is 10v not 4 or 5.  If I start the car with the remote, let it run one minute, hit the start button again to shut the engine off, the parking lights stay on 2 mins and the radio stays on for 10 minutes. I timed them. Also if I let the car run 15 minutes and essentially time out, the engine shuts off but the radio and lights stay on for 10 minutes. I was expecting the radio to shut off instantly just as if I had open the drivers door. Look forward hearing comments.

Login to reply View 1 answer(s)

16/03/2017

 Lincoln KOZ (750Pts.)

0

2010 MKX - PATS failure, no RAP

PATS failed to program with 2 key method, tried Dcryptor it failed too. Now all 8 key slots are full and vehicle locked out key programming. Also RAP does not work. Verified GRN/WHI to door side and GRN/RED to VEh side. Tested wires with meter, they are closed circuit and never change state.
Login to reply View 1 answer(s)

01/04/2016

 Ford Aaron Pino2 (140Pts.)

1

how to turn off radio after remote start turns off. 2014 f150

I want to know if there is a way after 15min the vehicle turns off can the radio turn off or do I have to let it say on for the 5min factory setting.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue