Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

06/02/2019

 Jeep Jeep Guy (160Pts.)

0

Viper smartstart not communicating with EVO ALL

I've installed a VSM350 in my 2008 Grand Cherokee, following the instructions (splice grey wire with black, plug in connector). The VSM350 has been activated by a local dealer and my viper online account is properly set up. I can update GPS information via the smartstart app (this confirms unit is powered up and communicating with the internet properly). I am not able to lock, unlock, or remote start using the app. When I attempt to lock/unlock or start, I receive the message "unlock failed at [time]" I have enabled H4 via flashlink. I live in a major city and the vehicle is parked outside, the issue is not related to cellular coverage; the app reflects that the vsm350 has 4 or 5 bars of signal strength. I appreciate any suggestions to enable the smartstart to communicate with the evo-all to enable the lock/unlock/remote start. Thank you
Login to reply View 1 answer(s)

01/02/2019

 Jeep Jeep Guy (160Pts.)

0

Programming EVO-ALL / CHRT4 with SmartStart VSM350

About a month ago, I successfully programmed and installed an EVO ALL with CHRT4 in a 2008 grand cherokee. The 3x lock would successfully initiate a remote start. I recently removed the EVO ALL to reprogram it with flasklink to enable H4 (smartstart). Upon reinstalling EVO ALL, I no longer had blue lights. I reprogrammed to the key and got the blue light to illuminate when clicking lock button. I connected the yellow to the yellow for ignition during initial install and that is still the case now. This yellow wire splice is the only wiring i've done outside of installing the CHRT4 harness. The current issue is that after reinstalling the EVO ALL, I do not get a red light on the EVO ALL after clicking 3x lock. The 3x lock is still enabled in flashlink, in addition to H4 being enabled. EVO ALL was already (and still is) flashed to the latest / best / recommended firmware. Given my inability to remote start with 3x lock before even connecting the smart start, i have left the smart start unplugged until i can resolve the failure to start with 3x lock using the key. I have tried re-flashing the evo-all with latest firmware in flashlink and starting over but am in the same position where i get blue lights but no red, and thus, no remote start using 3x lock. When vehicle is started via the key in ignition, EVO ALL gets a solid a yellow to indicate the evo-all knows it has ignition. My question is: What I'm doing wrong or do I not have connected properly to get my red light back after 3x lock so that the vehicle can start. Does H4 prevent use of 3x lock remote start?
Login to reply View 1 answer(s)

23/11/2015

 Jeep Ed Bradshaw (130Pts.)

0

CHRT4 installation with Parking Lights

In the installation instruction it notes:

If a parking lights (+) wire is use : they require more than

10Amp. Connect the remote-starter’s power directly to the

vehicles battery with the appropriate fuse.

 

Does this apply to connecting the (-) Parking Lights from plug A, on a Stand Alone installation?

Login to reply View 1 answer(s)

12/01/2015

 Jeep JEREMIAH PIERCE (160Pts.)

0

2008 Grand Cherokee Evo-All Stand alone will program but wont start

I installed the chrt4 stand alone unit on a 2008 grand Cherokee. It will program but will not start the vehicle. I tested to see if the yellow/blue wire had constant voltage(12V) and if the yellow/blue wire had voltage(12V) when attempting to start and it did. Im just at a loss for why it wont start. Any help would be appreciated. I bought this from the fortin website and supposedly it is updated with the latest software. thank you
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue