Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

08/06/2024

 Infiniti Carlos Esquivel (130Pts.)

0

After following procedure for bypass on Evo-all correctly decryptor says empty key data?

Tried multiple times and every time after getting the rapidly flashing blue light and after the alternating red and yellow when I go to decrypt it says key data is empty?
Login to reply View 1 answer(s)

18/02/2019

 Infiniti DavidF O'Sullivan (210Pts.)

0

Why won’t the EVO-ALL program in my 2013 Infiniti M37?

Standalone installation with T harness. I follow the steps exactly as they are written. Step 6 says hold key by start button and step on brake. Step 7 is the exact same process, but the BLUE and RED LEDs should illuminate. The RED illuminates briefly before turning off, and only the blue remains. The rest of the process does not work and the BLUE LED stays solid. In addition to this, the security/Immobilizer light on my dash is on solid when the car is running. Please, can anyone offer assistance?
Login to reply View 0 answer(s)

19/12/2016

 Infiniti Billy Bob (130Pts.)

0

2008 g35x no longer needs OEM keyfob?

I just installed the EVO-NIST1 standalone with the Fortin RF642W RF Kit on a 2008 Infiniti G35x according to Guide 24031 and have a couple comments & questions after playing around with it:

1) LOCK x3 works with the OEM fob, however it cannot remote stop the car with LOCK x3 again. This is known, so it is not a problem.

2) After remote starting the car and unlocking it (either with door button or with either of the fobs), I can open the door, step on the brake, and I am able drive away. That works as intended, but the problem is I can drive away without having the OEM key fob around. The instrument cluster screen does not say NO KEY like it normally would if the key has left the car. In other words, one would be able to drive off without having any remote on them as long as the car gets remote started followed by an UNLOCK signal. Are remote starts intended to bypass the need to have the OEM Intelligent keyfob for the take-over?

3) While the engine is off, the LOCK signal from either the RF fob or OEM fob will lock the doors and prompt the RF antenna's LED to start flashing (blue) and will not stop unless I press the UNLOCK botton on either remote. What is this flashing for? Can this be disabled? I do not need or want any alarms or extra security features. I am more concerned about it draining the car battery. Please advise.

4) After remote starting, the first press of UNLOCK with the RF fob ONLY turns off the Antenna's flashing. I have to press unlock a second time to unlock the car, however it would unlock all four doors at once. I had configured it through Flash Link (B1 on) to unlock driver door on first press, and lock all on second press but that isn't the case. What exactly happens on the first UNLOCK that stops the antenna's LED flashes? Can I get the unlock button to unlock the doors on first press?

5) How does IDLE mode pertain to push-to-starts where the key does not need to be in the ignition? I'm guessing it is not needed but just want to be sure.

6) I had to use the RL2 connector to get remote starter to work, although the guide says RL1 for G35. This might be the issue with folks who cannot get their '07 - '08's  to remote start.

Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue