Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

Key-Override-All, is the red light bulb on the module supposed to stay lit still even after programming is complete?

Remote start works perfectly fine even after red light remains on after programming

0

Key-Override-All, is the red light bulb on the module supposed to stay lit still even after programming is complete?

Remote start works perfectly fine even after red light remains on after programming

0

2010 ford escape KEY-OVERRIDE-ALL

I'm installling the KEY-OVERRIDE-ALL with a DEI remote start. When I attempted to program prior, I would see the LED start flashing, but programming didn't complete. Now when I attempt to program, the LED on the module stays on and the security light on the dash flashes rapidly. I've confirmed I have 12V on Red, Ground on Black, Ignition on Yellow, and remote start staus on Blue. Is there anything else i should try on this module? The module was purchased new in December and hasn't been installed in another vehicle.

0

Do I need the FLASH LINK UPDATER in order to install the KEY-OVERRIDE-ALL bypass module on a 06 F150?

I have a CRIMESTOPPER SP-402 ALARM REMOTE START installed. The white 4 pin DATA LINK cable that is supposed to connect to the EVO port on the alarm remote start did not fit and so I cut the clip off of the black 4 pin DATA LINK connector that supposedly goes into the ADS port of the CRIMESTOPPER ALARM REMOTE START module and plugged it into the EVO port. The connector did fit and I made sure the wires went in the port correctly as in the alarm remote start diagram. Did the programming on the bypass module as intended and I didn't get no blinking, off and on light,but just a steady red light. The truck did not remote start.

0

2002 Ford Focus / Key-Override-All / Will Not Program

Installed a Key-Override-All with a Crime Stopper 'CoolStart RS4-G5'. The Crime stopper works great with a key in the ignition only to satisfy the transponder. I have tried several time to program the Override unit with no success. I am using Connection (1) with the Data Link. The RX,TX and IGN wires are connected directly to the ignition switch transponder. The Blue wire is connected to the Yellow/Black on the Crime Stopper (Ground When Running (Bypass Module). I am using Program (2). I press the programming button and plug in the 'Black Connector' and the (6) pin connector. The red light comes on. I than program the keys and than hit the remote start. The red light blinks (3) quick blinks and thats it. The car never remote starts with teh 'Override' however the car will remote start and perform predictably as long as there is a PATS key in range of the transponder ring give me the understanding all is will except the 'Override' module. Can you tell me what I am doing wrong?

0

Cannot progran key-override-all on my 2005 ford freestyle

I replaced an existing remote start on my freestyle do to poor range. All went well until i tried programing.Initially when programed vehicle remote started on first try,after that  the security light will flash all other functions work but no remote start. if i unplug override module and incert key in ignition vehicle will remote start. Red light on module will stay solid red until i press start button again to turn off accessories,than light will flash 8 times then stay on solid

0

2010 F150 Wiring

I have the key over ride all, trying to wire it to 1010 f150 the red light comes on but never changes whewn I program it, maybe i have a wire wrong, using the excalibur rs 140 dp starter can you help me wire it all correctly very confusing instruction with both units

1

Installation in 2005 Ford Expedition key-override-all w/ RS1-G4

Followed Iinstructions that were provided with modules. Hood open not installed yet and park lights not connected yet. On your site there are two sets of instructions for this truck. One set shows to plug in plug number 2 fist then plug 1 and the other set shows to plug in plug 1 first then 2. I have tried both ways and no luck. The Key-Override-All never flashes 10 times. I only have one key and am following the procedure for one key. It blinks twice. When remote start depressed the lights come on the accessories start to run but no starter and the anti-theft indicator ion the dash begins to flash. Pressing the remote again shuts off everything, the KOA blinks 8 times and extinguishes and the LED on the RS1-G$ begins to blink. I think this is a feature of the unit as an anti-theft deterent. Had someone else check wiring and attempt to program and they were unsucessful, too. Thanks

1

if fortin plugs into Prostart remote car starter, do I need to wire up the 6 pin conn.?

ford-focus-2010 prostart-CT-3371-remote-car-starter Fortin-key-override-all where does the blue wire 6-pin-conn wire to in the remote? (-) while running????

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue