Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

18/10/2014

 Hyundai leo kim (840Pts.)

0

2014 Tucson weird issue

I installed using 2013 tucson guide on 2014 Tucson. I used Evo-all and Compustar 6200 brain. When press unlock, Evo-all will unlock the car but did not disarm factory alarm. Factory alarm went off as soon as I opened the door, pushed unlock button again, then disarmed. Another thing is remoste starting issue. Car will crank but will not keep running. It is transponder bypass problem but starts on 2nd attempt. Is this firmware issue? This only happened twice so far since december 2013.
Login to reply View 1 answer(s)

15/09/2014

 Honda brian koven (130Pts.)

0

2007 civic + compustar cm6200 + evo all = no start/crank/ignition

installed a 6200 + blade ads into my girlfriend's 2011 civic without a hitch...fortin is giving me grief. remote start fob was successfully programmed and will operate door locks; but no start - no crank....no switched ignition...nothing.... I also noticed that the fob won't update the door lock status if i change door lock position with oem fob - this is something that occurs in my girlfriend's car. evo all is connected to cm6200 via 4 pin datalink connector and evo all was programmed successfully no problem (got to flashing blue lights with key in run position). only 1 programming procedure so pretty hard to mix it up with another. option 4-11 is set to fortin protocol (setting 2) in cm6200....i have verified this with op500 As per connection 4 diagram of evo all install manual i have cm6200 connector CN2 pin 11 (poc5, black) connected to evo all 20 pin connector pin 8 (dark blue) for ground while running and i have verified that POC5 for CN2 pin 11 is set to 0 (GWR) via OP500. I did come across some apparent situations with other vehicles where evo all 20 pin connector pin 1 yellow was mistakingly connected to vehicle ignition wire (ignition barrel 7 pin connector pin 2 yellow), but can't find any evidence of that when installing evo all in 06-11 civic. the only thing i can think of is whether or not it's worth trying to loathingly purchase the flashlink updater and switch cm6200 to ads protocol and do the same with the evo all? Other than that i'm at a loss...???
Login to reply View 2 answer(s)

15/09/2014

 Honda brian koven (130Pts.)

0

2007 civic + compustar cm6200 + evo all = no start/crank/ignition

installed a 6200 + blade ads into my girlfriend's 2011 civic without a hitch...fortin is giving me grief. remote start fob was successfully programmed and will operate door locks; but no start - no crank....no switched ignition...nothing.... I also noticed that the fob won't update the door lock status if i change door lock position with oem fob - this is something that occurs in my girlfriend's car. evo all is connected to cm6200 via 4 pin datalink connector and evo all was programmed successfully no problem (got to flashing blue lights with key in run position). only 1 programming procedure so pretty hard to mix it up with another. option 4-11 is set to fortin protocol (setting 2) in cm6200....i have verified this with op500 As per connection 4 diagram of evo all install manual i have cm6200 connector CN2 pin 11 (poc5, black) connected to evo all 20 pin connector pin 8 (dark blue) for ground while running and i have verified that POC5 for CN2 pin 11 is set to 0 (GWR) via OP500. I did come across some apparent situations with other vehicles where evo all 20 pin connector pin 1 yellow was mistakingly connected to vehicle ignition wire (ignition barrel 7 pin connector pin 2 yellow), but can't find any evidence of that when installing evo all in 06-11 civic. the only thing i can think of is whether or not it's worth trying to loathingly purchase the flashlink updater and switch cm6200 to ads protocol and do the same with the evo all? Other than that i'm at a loss...???
Login to reply View 2 answer(s)

09/09/2014

 Chevrolet tvcity (190Pts.)

0

06 Avalanche factory alarm goes off intermittently

this unit has been in use for about a year & now sometimes when unlocking doors the alarm goes off. when you open the door. Using evoall with compustar CM 6200. Any suggestions on what may be causing this. We reprogrammed the evoall but problem still persists. Not able to get the unit to act up in the shop. Thanks in advance Don
Login to reply View 1 answer(s)

16/05/2014

 Nissan (Pts.)

0

evo-all with compustar

Hi. What exactly do I set the EVO-All protocol to d2d with a compustar cm6200? Will it have that option when I flash it? first time DIYer here. Thanks.
Login to reply View 1 answer(s)

07/12/2013

 Dodge tvcity (190Pts.)

0

evoall loses memory when battery disconneted

installed in 2005 dodge ram with compustar 6200 in data mode service #001A06 238980 replaced with another unit seems ok should i try in another vehicle with different download or send back thanks don
Login to reply View 1 answer(s)

19/11/2013

 Jeep autosoundnh (140Pts.)

1

2011 jeep patriot security light flashes after take over?

I have installed an EVO-CHR with THAR-CHR2 and Compustar 6200. After taking over with the key and pressing the brake the security light flashes constantly until the vehicle is shut off and restarted. Is there a fix? Thanks
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue