Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

Output wire for trigger

On the evo one, is there a wire ouput that i can use to turn on my dash camera?thank you!

0

connection E1 is made and the rest of the wire is left unused?

for guide 35051, connection e1 doesnt show a continuation arrow, does this mean the rest of the oem wire is unused?

1

2018 Subaru Impreza Key start - Evo-one w/T-harness instruction about IMO wire.

THAR-ONE-SUB THARNESS INSTALLATION guide (Guide #64451) Rev20170427.

Page 3

"IMO wire On the green 20 pin connector"

RED/WHITE wire is not present on this vehicle.

Is there an updated instruction guide?

Thanks.

 

Update: 07/14/2018

I just found the IMO wire.  It is the White/Lt.Blue wire on the 20 pin grey connector, on the back of the fuse box.  WireColor.com lists it as the "Body Integrated Unit, connector Q, 20 pin connector, pin 14, White/Lt. Blue"

This White/Lt.Blue wire is much easier to get to than the  "Red/White wire on the green 20 pin connector, on the Junction Connector" that is listed in the THAR-ONE-SUB1 THARNESS Installation guide, Rev. 20180627.

Maybe Fortin can update this Installation Guide to include a Note that says:

"if the Red/White Wire is not present on the Junction Connector, then use the White/Lt.Blue wire on the grey 20-pin connector on the back of the fuse box."

The installation was a success and the Remote works great.

0

Relay needed for 2nd starter wire Subaru Forrester '10

I've got a Python 4105 remote start with a Evo All. The wiring connection diagram has Starter1 out and Starter2 out, both positive, going into the python. Problem is there is only one wire for Starter out in the python. How do I do the second starter wire? I've seen some on the 'net say you need to wire it with the fist with a relay, but it has not been on Subarus. If that is the case, what type of relay and how do I wire it with the starter wires? 

Also, the python had two fused wires for 12 volt input, but there is only one wire on the car's ignition harness for 12v. Do I wire all three together, or just not use one of the inputs on the python?

0

Which Start wire to use on Forester 2009 ?

I recently acquired a 2009 Forester. Using a Fortin Evo-All and a Crime Stopper RS2-G3 remote starter I cannot figure out which Start wire to use. 1) Your installation guide suggest the use of Start wires Ter 1 (White/Black) and 2 (White/Red) while the RS2-G3 connector only has one Start wire (Brown). How should I make the proper connection(s) ? 2) As well, the remote starter has two (2) Constant 12V (+) Input Red wires on its 6 pin power harness. Should both of them be connected to the RS2 (+) 12V white wire of the Forester Ignition harness ? PS. I see that on the Evo One installation you use a relay on the Start Ter 2 wire.

0

Which Start wire to use on Forester 2009 ?

I recently acquired a 2009 Forester. Using a Fortin Evo-All and a Crime Stopper RS2-G3 remote starter I cannot figure out which Start wire to use. 1) Your installation guide suggest the use of Start wires Ter 1 (White/Black) and 2 (White/Red) while the RS2-G3 connector only has one Start wire (Brown). How should I make the proper connection(s) ? 2) As well, the remote starter has two (2) Constant 12V (+) Input Red wires on its 6 pin power harness. Should both of them be connected to the RS2 (+) 12V white wire of the Forester Ignition harness ? PS. I see that on the Evo One installation you use a relay on the Start Ter 2 wire.

1

2018 Subaru Impreza Key start - Evo-one w/T-harness instruction about IMO wire.

THAR-ONE-SUB THARNESS INSTALLATION guide (Guide #64451) Rev20170427.

Page 3

"IMO wire On the green 20 pin connector"

RED/WHITE wire is not present on this vehicle.

Is there an updated instruction guide?

Thanks.

 

Update: 07/14/2018

I just found the IMO wire.  It is the White/Lt.Blue wire on the 20 pin grey connector, on the back of the fuse box.  WireColor.com lists it as the "Body Integrated Unit, connector Q, 20 pin connector, pin 14, White/Lt. Blue"

This White/Lt.Blue wire is much easier to get to than the  "Red/White wire on the green 20 pin connector, on the Junction Connector" that is listed in the THAR-ONE-SUB1 THARNESS Installation guide, Rev. 20180627.

Maybe Fortin can update this Installation Guide to include a Note that says:

"if the Red/White Wire is not present on the Junction Connector, then use the White/Lt.Blue wire on the grey 20-pin connector on the back of the fuse box."

The installation was a success and the Remote works great.

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer