Questions & Réponses

Hello, I am looking to get remote start only for my '19 Ram 1500 promaster. It does not have remote start or alarm now. It uses a standard turn key. According to the website it says I can use the EVO-ONE. Looking at the install instructions on page 5, it shows what looks to be a remote starter module of some sort?

Am I looking at the right instructions for this setup?

If so, do I need another part?

Also, is there a t-harness made for this yet?

Thanks!

as soon as the 4 pin connector is plugged in with the button pressed in to the evo -all the red light comes on and stays on. When starting the programing prossses accidentlly released the button on red.

2019 RAM 2500 Push to Start GAS

(What I wired)

THAR-CHR6 Harness:  I wired from the EVO ALL  A1  to the purple and white on the Igintion BCM module. A10 to Lt.Blue of T harness, A20 to the Lt.Blue/Black of T harness, with an OHM meter I ringed them out (they are connected). I tied the red connector  D3 & D1 together and soldeir together at the T harness as discribed.  Can 1 LOW connection C4 from the EVO to the Yellow of CAN 1 connector on the truck. Can 1 High connection C3 from the EVO to the Brown and White of CAN 1 connector on the truck. 

(plugged it the remaining plugs by the steps discribed into the EVO ALL) 

Issue I have: I go though steps 1 & 2, however when I plug the 20 pin connector in the light the blue light goes out. (no lights are on).

I updated and flashed the EVO to Firmware 74.[38]  Hardware inside 7.0  however, the the orange box says Recimmended firmware is not loaded 63.[02]  then there is a green Update to that version aside it. 

What can my issue be. Thank in advance for any help! 

2019 RAM 2500 Push to Start GAS

(What I wired)

THAR-CHR6 Harness:  I wired from the EVO ALL  A1  to the purple and white on the Igintion BCM module. A10 to Lt.Blue of T harness, A20 to the Lt.Blue/Black of T harness, with an OHM meter I ringed them out (they are connected). I tied the red connector  D3 & D1 together and soldeir together at the T harness as discribed.  Can 1 LOW connection C4 from the EVO to the Yellow of CAN 1 connector on the truck. Can 1 High connection C3 from the EVO to the Brown and White of CAN 1 connector on the truck. 

(plugged it the remaining plugs by the steps discribed into the EVO ALL) 

Issue I have: I go though steps 1 & 2, however when I plug the 20 pin connector in the light the blue light goes out. (no lights are on).

I updated and flashed the EVO to Firmware 74.[38]  Hardware inside 7.0  however, the the orange box says Recimmended firmware is not loaded 63.[02]  then there is a green Update to that version aside it. 

What can my issue be. Thank in advance for any help! 

2019 Ram 1500 push to start Unable to get past step 6 blue led will not stop flashing when Start/Stop button is pressed to turn off ignition.

VIN: 1C6RREFT6KN568083

Hardware version is 6.0  

Firmware version is 63.[01]  

flash limit 2/8  

Have tested contunity on all leads for completeness, wires are in the correct place and not incorectly tied.  

Flash Link  

Hardware version 4.0  

Firmware version 4.[05]

I have tried pressing unlock on oem remote when blue is flashing and ignition is off.

Outcome: Truck responds by unlocking doors and blue led is still flashing rapidly.  

I have tried resetting the unit and attempted to program. I also toggled push to start on and attempted to program as well.

Outcome: I am still Unable to get past step 6 blue led will not stop flashing when Start/Stop button is pressed to turn off ignition.

I am still unable to get past step 6.

Fortin, what are the proper channels I can use to esclate this matter further. It has been several months of back and forth with no progress. I feel the only other way to get through to you would be by sharing my emabrising expierence on social media platforms. Before I do let me ask one last time...please help. 

Best,

Dylan Davila

2019 Ram 1500 push to start Unable to get past step 6 blue led will not stop flashing when Start/Stop button is pressed to turn off ignition.

VIN: 1C6RREFT6KN568083

Hardware version is 6.0  

Firmware version is 63.[01]  

flash limit 2/8  

Have tested contunity on all leads for completeness, wires are in the correct place and not incorectly tied.  

Flash Link  

Hardware version 4.0  

Firmware version 4.[05]

I have tried pressing unlock on oem remote when blue is flashing and ignition is off.

Outcome: Truck responds by unlocking doors and blue led is still flashing rapidly.  

I have tried resetting the unit and attempted to program. I also toggled push to start on and attempted to program as well.

Outcome: I am still Unable to get past step 6 blue led will not stop flashing when Start/Stop button is pressed to turn off ignition.

I am still unable to get past step 6.

Fortin, what are the proper channels I can use to esclate this matter further. It has been several months of back and forth with no progress. I feel the only other way to get through to you would be by sharing my emabrising expierence on social media platforms. Before I do let me ask one last time...please help. 

Best,

Dylan Davila

2019 Ram 1500 push to start Unable to get past step 6 blue led will not stop flashing when Start/Stop button is pressed to turn off ignition.

VIN: 1C6RREFT6KN568083

Hardware version is 6.0 

Firmware version is 63.[01] 

flash limit 2/8 

Have tested contunity on all leads for completeness, wires are in the correct place and not incorectly tied. 

Flash Link 

Hardware version 4.0 

Firmware version 4.[05]

I have tried pressing unlock on oem remote when blue is flashing and ignition is off.

Outcome: Truck responds by unlocking doors and blue led is still flashing rapidly. 

I am still unable to get past step 6.

2019 Ram 1500 push to start Unable to get past step 6 blue led will not stop flashing when Start/Stop button is pressed to turn off ignition.

VIN: 1C6RREFT6KN568083

Hardware version is 6.0

Firmware version is 63.[01]

flash limit 2/8

Have tested contunity on all leads for completeness, wires are in the correct place and not incorectly tied.

Flash Link

Hardware version 4.0

Firmware version 4.[05]