English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

07/10/2023

 Mazda William Roberts (130Pts.)

-1

Evo One, 2021 Mazda CX5 automatic, not getting blue led on step 4

It is set up on bypass firmware 85.12 and remote start firmware 1.26. I reflashed each firmware to the module in pro mode just be sure then reflashed the settings. It is set to the defaults with the wizard but I did switch to pro mode at one point to verify a few of the settings that were mentioned in the guide, A11 C1 and D2. Once I bring it to the car and plug in holding the button, blue led comes on and then I plug in 3 other cables (THAR-ONE-MAZ3 cable). I press ignition twice, it just cycles through the leds over and over. I've waited at least 2 minutes and it never stops cycling. I tried to read the voltage on the CAN BUS and it was 0.8-1.3V DC while this was going on. Any other things I can try to get the Dcrypt done? Thank you!
Connectez-vous pour répondre Voir 1 réponse(s)

19/08/2021

 Mazda Michael Jover (180Pts.)

0

2014 Mazda CX5 Manual - Installed EVO-ONE W/ THAR Lights blink blue does not stay on solid

Hello, I purchased an EVO-ONE kit along with the T-harness for my 2014 Mazda CX5 manual trans, push button start. I programmed the module originally with the Flash Link on windows 10 laptop, I installed it in the vehcle with the T Harness. I ran a wire for the hood switch and mounted it. I am unsure if I hooked up the clutch switch correctly, the picture shows it in series but the input goes straight into the module and then back around into the T Harness..I hooked it up to the ground side trigger. The module will not power up and stay on, if I hold the programming button or unplug the 6 pin and plug it back in the unit will blink all the LEDs and then they just all go out. The blue one will not stay on. Can I get some guidance guys? Anybody run into this before? I double checked all the plugs into the module, the T Harness plugs. Mike
Connectez-vous pour répondre Voir 3 réponse(s)

19/08/2021

 Mazda Michael Jover (180Pts.)

0

2014 Mazda CX5 Manual - Installed EVO-ONE W/ THAR Lights blink blue does not stay on solid

Hello, I purchased an EVO-ONE kit along with the T-harness for my 2014 Mazda CX5 manual trans, push button start. I programmed the module originally with the Flash Link on windows 10 laptop, I installed it in the vehcle with the T Harness. I ran a wire for the hood switch and mounted it. I am unsure if I hooked up the clutch switch correctly, the picture shows it in series but the input goes straight into the module and then back around into the T Harness..I hooked it up to the ground side trigger. The module will not power up and stay on, if I hold the programming button or unplug the 6 pin and plug it back in the unit will blink all the LEDs and then they just all go out. The blue one will not stay on. Can I get some guidance guys? Anybody run into this before? I double checked all the plugs into the module, the T Harness plugs. Mike
Connectez-vous pour répondre Voir 3 réponse(s)

19/08/2021

 Mazda Michael Jover (180Pts.)

0

2014 Mazda CX5 Manual - Installed EVO-ONE W/ THAR Lights blink blue does not stay on solid

Hello, I purchased an EVO-ONE kit along with the T-harness for my 2014 Mazda CX5 manual trans, push button start. I programmed the module originally with the Flash Link on windows 10 laptop, I installed it in the vehcle with the T Harness. I ran a wire for the hood switch and mounted it. I am unsure if I hooked up the clutch switch correctly, the picture shows it in series but the input goes straight into the module and then back around into the T Harness..I hooked it up to the ground side trigger. The module will not power up and stay on, if I hold the programming button or unplug the 6 pin and plug it back in the unit will blink all the LEDs and then they just all go out. The blue one will not stay on. Can I get some guidance guys? Anybody run into this before? I double checked all the plugs into the module, the T Harness plugs. Mike
Connectez-vous pour répondre Voir 3 réponse(s)

19/08/2021

 Mazda Michael Jover (180Pts.)

0

2014 Mazda CX5 Manual - Installed EVO-ONE W/ THAR Lights blink blue does not stay on solid

Hello, I purchased an EVO-ONE kit along with the T-harness for my 2014 Mazda CX5 manual trans, push button start. I programmed the module originally with the Flash Link on windows 10 laptop, I installed it in the vehcle with the T Harness. I ran a wire for the hood switch and mounted it. I am unsure if I hooked up the clutch switch correctly, the picture shows it in series but the input goes straight into the module and then back around into the T Harness..I hooked it up to the ground side trigger. The module will not power up and stay on, if I hold the programming button or unplug the 6 pin and plug it back in the unit will blink all the LEDs and then they just all go out. The blue one will not stay on. Can I get some guidance guys? Anybody run into this before? I double checked all the plugs into the module, the T Harness plugs. Mike
Connectez-vous pour répondre Voir 3 réponse(s)

11/01/2020

 Mazda Alex Macharia (130Pts.)

0

Mazda Failing Decryption process (not able to get a solid blue)

I have tried to run the exact process for initializing decryptor for a CX-9 install, starting with diconnecting the neg battery terminal and then connecting the steering wheel white terminals into the T harness,reconnecting battery power and then holding down the button on the Evo one module while plugging in the 6 pin connector. I have not been able to get the module to set the blue solid light. Anyone run into this? Module was programmed correctly via flashlink
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer