English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

03/12/2024

 Mazda Kong Vang (250Pts.)

0

2013 CX-5 Cranks But Won't Start M/T

EVO-ONE. I have the THAR-ONE-MAZ3 harness. White cable for clutch bypass is connected. Not sure what's going on. I've tried changing the programmable output from 2.1 (default) to 2.2 (I think it should be this one?) and still no luck. It will try to crank for a few seconds, then shut off then tries again for a few seconds but won't start. Yellow jumper was cut when I received it, but it is currently twisted together until I verify what the issue is then I'll do a more rigid connection. I don't have the hood pin switch connected, my kit didn't come with it. Not sure if this is preventing it from starting or not. I have tried enabling and disabling A11 for this but still no luck with remote start. SN: 002B04 643579
Connectez-vous pour répondre Voir 1 réponse(s)

10/02/2024

 Mazda Kevin Hunt (130Pts.)

0

Manual CX-5 Crank no start

2014 Mazda CX5 ; manual push to start ; Evo-one w/MAZ THAR ; SN 002b04 638289

Cranks but doesn't start. All fob functions work, car runs normally, and it goes into ready mode and shuts down after exiting. Won't autostart after getting out of the vehicle - what am I missing? Valet mode off.

Using default settings with the plug&play harness.

Firmware 85.14

A1 through A-10 : ON

A11 OFF ; B1 OFF ; C1 ON

D2 ON

D3-D5 : OFF ; D6 ON

Firmware 1.26

2 through 15 : option 1 (default)

16.5 ; 18.1 ; 19.1 ; 20.8 ; 21.2 ; 24.1 ; 25 (off) ; 26.1 ; 29.1 ; 30.1 ; 31.1 ; 32.1 ; 33.2 ; 34.1 ; 35.1 36.3 ; 37.1 ; 38.1 ; 39.1

Connectez-vous pour répondre Voir 1 réponse(s)

29/07/2023

 Mazda Richard Arms (130Pts.)

0

2019 Miata manual, crank but no start. Getting three flashes after failed attempt.

Evo-one 002B04310069
Connectez-vous pour répondre Voir 1 réponse(s)

08/01/2023

 Mazda moosespectacles (160Pts.)

0

(15 Mazda 3) Car cranks but ignition does not turn on, after steps 1-12

I can get through steps 1-12 (though the security light never displays on the dash), and when the ignition is supposed to turn the car on, the dash lights turn on, I hear a crank, but the car never starts. However, I do get the red and yellow lights flashing, so I tried connecting to the PC to use dcryptor, thinking maybe it will turn on after, but still no luck. Does anyone know what the issue is? I'm using THAR-MAZ1 with the Evo-All and following guide 62681. Everything is plugged in, and the only wiring done is the Lt blue to Lt blue on the 32 pin connector, and the Lt Blue/Black to the red on the 32 pin connector. Am I missing a connection, perhaps an ignition wire? Any help will be greatly appreciated. Thank you in advance.
Connectez-vous pour répondre Voir 0 réponse(s)

11/03/2022

 Mazda Rohaan Arshad (160Pts.)

0

'21 Manual Miata cranks, but doesn't start

I own a 2021 Mazda MX5 Miata RF GT in a manual transmission. I'm using the EVO-ONE with the THAR-ONE-MAZ3 T-Harness. I've made sure to splice the white cable (Manual only) with the corresponding white pin A5 on the 20 pin connector for the clutch bypass .I've actually gone through a couple configurations and at this point, I chose to use suggested settings as well as the settings the manual insisted. I've also enabled 3x OEM lock since I want to use my own remote. So far, once I initiate the ready mode sequence, I triple click the lock button and the car cranks for a bit but doesnt start. I've been through the settings a couple of times over to check everything and its not clear to me what might be causing it. Please let me know if there is any additional wiring needing to be done or a certain setting that's causing it not to work. I'm so close to a successful start, yet so far.
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer