Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

2019 Mazda CX-5 (A/T & PTS) Alarm activating when remote starting (OEM keyfob/ 3xLock)

Sometimes when I try to activate remote start with my OEM key fob by pressing the lock button three times my car alarm will go off and then I press unlock and the car starts

0

EVO-ONE 2015 Mazda 3 Manual Transmission - Remote Start Will Not Activate

2015 Mazda 3 Grand Touring Hatchback, push-to-start, smart key, manual transmission.  I cannot get the module to start the vehicle with 3x OEM remote lock.  I've followed the instructions for manual transmission in Guide #68261.  My EVO-ONE serial number is 002B04 298695 and it is dated 09/2022.  Here's what I've done:

    EVO-ONE flashed with Firmware 85.12. Using T-Harness. Yellow loop wire NOT cut White wire labeled "for manual transmission only" on the T-harness is connected to the white wire coming out of the 20-pin connector.  These wires are just butt spliced with no other connection. DCryptor process to enable key bypass appears to have been successful from all FlashLink software messages. Remote starter option 33 is set to mode 2 for foot brake - handbrake - release foot brake Ready Mode process. Remote starter option 38 is set to mode 2 to enable 3x lock with OEM remote. Bypass option C1 is on for OEM remote status monitoring. I did not install a hood pin.  I am not concerned about remote starting while the hood is open.  Bypass option A11 is set to "off." Bypass options for foot brake, hand brake, door output monitoring are all set to "on."

To enable ready mode, I depress the foot brake, engage the hand brake, release the footbrake, and exit the car while it is still running without pushing the start button.  The car just sits there and runs, nothing happens when I close the door and walk so that the smart key is out of range.  I also tried doing this with shutting the car off before exiting and was still not able to remote start the vehicle.

When I press the lock button on the OEM remote, the blue LED on the EVO-ONE blinks indicating it is reading the CAN bus messages.

When the car is running, the yellow LED on the EVO-ONE is steadily illuminated.

At no point does the red LED on the EVO-ONE illuminate.  It does not turn on after pressing the OEM remote lock button 3x.

When I press the OEM lock button 3x after the above ready mode process, absolutely nothing happens except the car horn beeps on the 2nd and 3rd presses like it normally would.


Thanks in advance for your help.

 

0

i-stop feature is not work if using Take Over procedure

Hi everyone,

 

I have a Mazda CX5 and installed Fortin Evo One with Thar-One-Maz3 T-harness. Everything works fine except:

    I remote started the car by 3x locks, get in the car and press Start button (without pressing brakr pedal) then drive, i-stop feature did not work anymore. I-stop works as normal if I press brake pedal to stop engine then press Start button and drive. 

Is there anything I can do or configure to make i-stop works after performing "take over" procedure? 

 

Thank you,

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer