Questions & Réponses

I just purchased an EVO one with a THAR-ONE-HON1 T-harness for a 2011 Honda CRV. I successfully programmed the module prior to installing it in the vehicle using the Fortin Flashlink V4. I installed the T-Harness onto the vehicle without connecting any of the horn, parking lights or door lock provisions at first, so that I can perform the key bypass procedure. I was able to set this up successfully with no issues. I even tested that the vehicle would be able to be started via the 3x lock procedure. All was perfect.

I then proceeded to connect the parking light connection along with the horn and door lock connections. All of the instructions were used based off of the 57711 guide. I also used the activation code for the wirecolor website prior to splicing any connections. I also verified with the colors with my service manual and all was good. After splicing into the factory connections for the horn, parking lights and the door lock, I proceeded to attempt the remote start procedure and the vehicle. The parking lights and horn worked flawlessly, the door lock however would not unlock. I had to manually open the door to unlock it. I then proceeded to turn off the vehicle, I figured maybe it was a glitch.

I then proceeded to attempt to remote start the vehicle again and this time the vehicle would not start. The module would not even light up, no color would show. The module seems to be dead now. I have verified all connections twice before splicing into the factory harness and then proceeded to verify another two times afterwards just to make sure that I did not accidentally wire anything incorrently. Everything is connected exactly as the instructions show. I'm not sure exactly what could've caused the module to stop working with everything being connected properly. Please help. Thank you!

I am trying to install an EVO-ONE remote starter on my 2015 Honda CRV Push-to-Start. I am using the T-harness. I connect the 24 and 28 pin connectors correctly. When I hold down the program button and plug in the 6-pin plug, nothing happens. No lights turn on on the module. I know I am doing this part correctly. Previously, I had an EVO-ALL and got it set up correctly (but I ditched that effort because I couldn't get the Crimestopper remote starter to work and just bought the EVO-ONE). I did this process on the EVO-ALL (using the 4-pin data link wire) countless times without difficulty - this part was never the problem. Why don't I get any lights at all when I hold down the program button and plug in the 6-pin connector on the EVO-ONE? I have updated both the "bypass" side to 73.31 and the "remote starter" side to 1.24 using the Flashlink. I updated the bypass side, then I unplugged it from the computer. Then I plugged it back in and updated the remote starter side. On the bypass side, I have C1, D2, and D6 enabled. On the remote starter side, I have 38.2 enabled. None of that even matters because the module won't even light up when I plug it in! Of note, if I have the 6-pin main harness plugged into the EVO-ONE and turn the car's power on, it does flash some lights - so I know it is getting power.

This is my only concern: I am using the T-harness that came with the EVO-ALL + Crimestopper kit that I purchased online prior to giving up on that and switching to the EVO-ONE. The label on the T-harness says "THAR-HON3". It does not say "THAR-ONE-HON3". However, it appears to be the exact same harness as the THAR-ONE-HON3. It has all of the same connectors. Please do not recommend to me that all I need to do is buy the T-harness that is specifically called "THAR-ONE-HON3" unless you are absolutely certain that this is the issue because I have already spent more money than I should have trying to install a stupid remote starter on my vehicle. I only see one type of T-harness available on this website for my push-to-start vehicle, so I don't think that there is really a difference between the two. However, if you know for a fact that there is a true difference between "THAR-HON3" and "THAR-ONE-HON3" and that the "THAR-HON3" T-harness is incompatible with the EVO-ONE, I will buy the THAR-ONE-HON3 T-harness.

Sorry for the long post. I am just trying to anticipate any follow up questions and go ahead and address them. Thanks in advance for your help. I'm almost ready to throw all of this in the trash and buy a car with remote start on it.

Hello there,

I have an EVO-ALL with firmware to date Ver.73.14.  I am trying to program the unit for 2015 CR-V (Push-to-Start) from the Programming Procedure instructions/GUIDE#23341/REV.:20141112.  I was able to follow up to step 4 (page 3/5)  then I stucked at step 5 because the "RED and BLUE LED still flash 2x/sec"...even I tried to "Push the Start botton 2x on the vehicle..." and many times later...still failed?

I did not see the "YELLOW LED" flashing on? or BLUE LED blinking? or any alternation between of the "YELLOW and RED LED" on?

Can you please tell me what did I miss here?

Thank you very much,

Nhut