Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

Evo one only responds when its in valet mode

Evo one s/n 002B04108567 programs correctly with 2010 dodge challenger standard key wire to wire oem key fob and blue light flashes after when pressing lock or unlock , yellow light turns on when starting the car. The problem is minutes later the unit appears to end in in valet mode , red light on the side near yellow cut wire is on. When I take the unit out of valet mode , red light turns off but I no longer receive the blue light when locking or unlocking the car with the oem fob. When I attempt to remote start the car 3x lock the eed light turns on then the yellow light turns on but the car doesn't crank at all and only attempts to try 1x even though programming is set for 2x attempts. Then I get 4 clicks or flashes from the module. I followed guide #94481 for installation and have tried the basic bear options with my flash link 2 updater on 59.02 and 74 38 and 1 25 firmwares. I notice to anytime I try to run the module on the FL updater the FL updater has to be updated each and every time with 4 05 ? Any help appreciated , no oem alarm

0

Can I get my Evo One Reset ?

Flash Limit Reached on Evo One. Please Reset. S/N 002B04108567 And should I do the recommended update that is suggested by the flask link update tool or do I stick with the version on the instruction. 2010 dodge challenger standard key standard installation , no T harness. Bypass* Recommended version 74.39 OR instruction version 59.01 Remote start* version 1.25 Flash link 2 unit version 4.05 has to be re updated everytime I use it for reason. (windows 11)

0

2006 Ram 2500 Solid Blue Light goes out when ignition turns on during programing.

2006 Ram 2500 Solid Blue Light goes out when ignition turns on during programing. Answer: The fix for me was to only use the grey Can wire. i removed the grey with black stripe wire and i was able to finish the install.

0

cant get horn to trigger or trunk to pop

I have a siren positive connected to E1 thick white wire and siren neg connected to orange/black wire and the siren works. I have the horn wire under driver side dash green/orange wire also connected to the thick white wire. Horn honks when arming evo one alarm but not sound when alarm is triggered. What am I doing wrong ? Which option in #12 should be checked , siren + E1 white - horn, right ? Also I've tried several different wires to get the trunk to pop with no luck ! I'm using factory fob that has trunk pop button. Evo one , wire to wire , no factory oem alarm.

0

evo one can't get solid blue stay on step 1-3 om 2008 dodge ram 2500 diesel

can't get solid blue led stay on ptogramming 1-3

0

Parking Lights Resistor

On my 2005 dodge dakota installed evo one and it all works properly however my parking lights keep going off as ther resistor fails. I used a 1.5k ohm 1/2watt metal film resistor. Should i use a higher watt resistor or type of resistor such as carbon film?

0

Evo One Install would I still use Dk. Blue. for hood pin whrn its hooked to vehicle key sense wire?

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer