English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

21/02/2022

 Lexus Dat Vu (260Pts.)

0

Autolights, foglights and high beams stopped working after installing EVO-RS TOY6 on 2017 Lexus NX200t

Just installed EVO-RS TOYT6 (EVO-ALL + TOY6) on 2017 Lexus NX200t for OEM remote start (3xLock) and works fine. The only issue is that autolights do not work (lights do not turn on even if it's dark outside) and foglights do not work, either. EDIT: Also noticed high beams won't turn on, either. The "symbol" indicator shows up on the dash but the physical beam lights do not turn on. Anybody has a fix for this?
Connectez-vous pour répondre Voir 2 réponse(s)

23/11/2019

 Toyota John Klimek (430Pts.)

0

Automatic lights do not work after install on 2018 RAV4

I've just finished installing the wiring on my 2018 RAV4 XLE Hybrid and now the automatic lights do not work.

 

NOTE: I've only connected the wires and the EVO-ONE is not connected yet.

 

I'm using the Fortin THAR-TOY6 harness and I've connected everything exactly as described in the manual:

 

1) Purple wire to (+) STARTER.  (soldered connection)
2) White/Black wire to (-) START/STOP.  (soldered connection)
3) +12V and GND wired to OBD2 per manual.  (used Posi-Tap connectors;  there is absolutely no way to pull OBD2 connector far enough out to solder wires behind connector)
4) "A" harness/passthrough connected to Main Body ECU.

 

I do not have an EVO-ONE yet but I wanted to finish the wiring.  All car functions still work properly except the automatic lights.

 

What can I check to see why they are not working?  I was extremely careful during installation and can't imagine why it's not working except that I don't have the EVO-ONE installed yet.

 

Connectez-vous pour répondre Voir 1 réponse(s)

15/08/2017

 Chevrolet Pat Lynch (1120Pts.)

0

Disarm Pulse.

Hello I have an Evo One setup up with a 2017 Chevy Cruze. Does the Disarm output A6 Orange on the Evo One give a negative pulse outpiut on remote start. I need a neg pulse to disarm the auto lights and as the GWR wire will be used for starter kill, this seems to be the best option. Regards Pat Lynch
Connectez-vous pour répondre Voir 1 réponse(s)

21/10/2014

 Kia Todd Voigt (610Pts.)

0

driver door will not lock after remote start

2013 Kia Sorento LX pushbutton start, evo all hardware 6, firmware 4.18, remote starter brain compustar cm800. Reference used for installation ... evo-all_kia_sorento_-_push-to-start_(2011-2013).rev-20140626.pdf from this site. Installation appears to be functioning ... doors will lock and unlock via remote starter remote. I have the remote starter set to unlock before start, lock after start ... if the doors aren't unlocked before start, the OEM security system complains (horn honks... and honks). The doors unlock, the vehicle starts successfully, but when the remote starter attempts to lock the doors after start, all doors EXCEPT the drivers door lock... I can see the lever flip to lock on the drivers door, but then it immediately flips back to open again. Would this have something to do with the A10 pin hookup on the evo all? ... the reference says it goes to the "driver door pin" ... but the illustration looks contradictory ... the expolded view of connector #4 on the vehicle shows a different pin location than the unexploded one. Maybe I have the wrong pin there? What is that supposed to do and how can I test if I have the right one selected? Any help would be appreciated. I can't use it this way. Cheers.
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer