Recherche rapide
Trouvez la bonne solution pour votre véhicule.

Questions & Answers

How do I hardwire the brake for EVO-ONE in a 2010 Hyundai Accent (Guide #60801)?

0 votes
Have additional questions regarding answer (by Derek) to original question; both posted below for clarity...
1.  Had already tried reversing the can bus wires (no effect) and the option 20.2 in the remote starter was already set by default.  What would 20.n be if it was not 20.2?
2.  Do all default settings assume I have PATS data wires?
3.  How do I hardwire the brake?  The only place brake is mentoned in the #60801 guide is in "Vehicle functions supported in this diagram..." at the top of page 1.
4.  I also purchased the two way RF system (haven't tried to hook up yet obviously).  Will hardwiring the brake and/or setting option 20.2 affect the function of that system, particularly the feedback that tells you the car is running?
5.  Answer below said: "By doing this you will skip the need to even program it on the blue light."  Does this mean no programming at all is required?  Should just start?  Key is bypassed?
6.  If the above doesn't work, is it time to send everything back?
BTW, I don't care about alarm.  Just want remote start.
Thanks, Mike
That is a typo in the troubleshooting guide. As the website states it is indeed a KHY1. I have corrected it.
You can try flipping the can bus wires see if that works. If it refuses to program I suggest the following.
Since you only get tach and frootbrake from the can bus, as long as your car is automatic transmission:
-Set option 20.2 in the remote starter
-Hardwire the brake.
By doing this you will skip the need to even program it on the blue light.
Having trouble programming a EVO-ONE for my 2010 Hundai Accent.  It has the thar-one-khy1 T-harness.  Before programming I loaded the latest firm ware; 76.[54] for bypass and 1.[24] for remote starter.  I loaded the suggested options for both and made sure the remote starter setting from the install guide (2.2 and 32.5) were correct.  The car does not have the PATS data wires (no imobilizer).  I used guide #60801 to install and programming method 2.  The blue light does not flash in step 4.  Just goes out and will come back on when the key is returned to off.
I used the troubleshooting guide associated with the #60801 installation guide on the flash link manager (says it is for thar-one-khy2 T-harness).  The wiring is correct and have verified continuity.  Voltages on the CAN wires are roughly 2.35 and 2.65.
Crutchfield sent me a second one when the first wouldn't work in case thre was something wrong with the unit.  Got the same results with both.  Oh, and I did cut the yellow loop for the automatic transmission.  Are there any bypass/remote starter options that I might change - or anyhing else for that matter - that might get this thing working or is it just not going to work on my car?


posté Jan 30, 2020 dans la catégorie Hyundai par Michael McKee (160 points)
modifié Jan 30, 2020 par Michael McKee

1 Réponse

0 votes
If your vehicle does not have an immobilizer, no need to program the unit to the car. No need to program CAN-BUS either. Just plug the EVO-ONE, all lights will flash about 20 times then stop.


The vehicles brake  signal car will need to be connected to the BLACK wire in the 20-pin connector.

Once that is done, you will be able to program the RF-KIT and test your remote starter.
répondu Jan 30, 2020 par Robert T (275,350 points)

Le savoir-faire au travail est l'ultime outil en ligne pour les installateurs de démarreurs à distance et de systèmes d'alarmes. Le site fourni des informations sur le cablage et des photographies détaillées des processus d'installation.


Recevez nos nouveautés
par courriel.