Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

11/09/2023

 Toyota Tacoguy (130Pts.)

0

Ex-One was just working, now it doesn't, and won't program.

Bought a 2015 Tacoma where the Ex-one didn't work. I diagnosed as a split wire, repaired the wire, programmed the fobs, and got it to work. On and Off, Door Lock and everything worked. Then I unplugged it to run it through my dash, and once everything was back together, now nothing works. I can't even press the valet/programming button to enter programming mode. When I turn the key in the ignition, the yellow light comes on, but that's it. I have tried touching a paperclip to both valet switch terminals to check if it's the button that is malfunctioning but the red light still never goes on. What would cause the whole box to suddenly stop working?? Again, I try to press the valet button, and the red light never comes on to progress through programming mode. Is there a button combination on the fobs? Or a factory reset on the receiver that I can push with a pin? Have I accidentally put it into "valet mode" with a button combination? I do not have the manual because I bought the truck used, and there is no support on this website, and the Fortin troubleshooting app seems to be an incomplete app, where most buttons don't work, and on one screen where it asks me to choose a diagram, the only options are "yes" and "no"...
Login to reply View 1 answer(s)

24/11/2022

 Toyota kenneth rocha (160Pts.)

0

Evo-all will not work

Hello. I am attempting to setup an Evo All. SN#001A07406644. I go through the guide and I can not get the unit to start the vehicle. Can someone help me figure out what is going wrong? Vehicle is a 2019 Toyota Highlander. The last attempt I made I performed the in car programming. The did the Dcryptor program. After plugging the unit back into the car I have no leds until I go to on ignition position then yellow led comes on and stays on until the car is shut off.
Login to reply View 1 answer(s)

24/11/2019

 Toyota Chris S2 (300Pts.)

1

2008 4Runner - KEY BYPASS Programming procedure fails, does not detect key

I just installed an EVO-ONE with T-harness on my 2008 Toyota 4Runner. All 7 connections per 24121 have been completed. The 20-pin white harness and the 6-pin T-harness are connected to the EVO-ONE. When I attempt to program the Key bypass, it fails at step 5. The EVO-ONE does not appear to detect the key insert and the red led stays lit and does not start flashing. I double checked all connections and they appear in tact. The EVO-ONE is running the following firmware based on the recommendation of the Flashlink Manager software. Remote Starter: v1.24 Bypass: v79.54 Any ideas on what is causing this? thanks!
Login to reply View 1 answer(s)

31/03/2019

 Toyota Brian Hutchins (240Pts.)

0

Evo one wont finish programing

I have a 2011 Tacoma gkey. I've tried evo all and evo one. When programming I get to the point where the LEDs flash rapidly red and blue. Turn the key on and I dont get a blue led solid or flashing. I notice on the diagram that the obd2 hook up is marked as imo wire.my diagram says its sils. My imo is behind the glove box. Is this what can cause my issue
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue